AT91RM3400-DK Atmel, AT91RM3400-DK Datasheet - Page 377
AT91RM3400-DK
Manufacturer Part Number
AT91RM3400-DK
Description
KIT DEV FOR AT91RM3400
Manufacturer
Atmel
Series
AT91SAM Smart ARMr
Type
MCUr
Datasheets
1.AT91RM3400-DK.pdf
(461 pages)
2.AT91RM3400-DK.pdf
(2 pages)
3.AT91RM3400-DK.pdf
(25 pages)
Specifications of AT91RM3400-DK
Contents
Evaluation Board, Software and Documentation
Processor To Be Evaluated
AT91RM3400
Data Bus Width
32 bit
Interface Type
RS-232, USB
For Use With/related Products
AT91RM3400
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 377 of 461
- Download datasheet (6Mb)
Command-
response
Operation
1790A–ATARM–11/03
Both read and write operations allow either single or multiple block transmission. A multiple
block transmission is terminated when a stop command follows on the CMD line similarly to
the sequential read.
The MCI provides a set of registers to perform the entire range of MultiMediaCard operations.
After reset the MCI is disabled and becomes valid after setting the MCIEN bit in the MCI_CR
Control Register. The bit PWSEN allows saving power by dividing the MCI clock by 2 power
PWSDIV (MCI_MR) when the bus is inactive.
The command and the response of the card are clocked out with the rising edge of the MCCK.
All the timings for MultiMediaCard are defined in the MultiMediaCard System Specification
Version 2.2.
The two bus modes (open drain and push/pull) needed to process all the operations are
defined in the MCI command register. The MCI_CMDR allows a command to be carried out.
For example, to perform an ALL_SEND_CID command:
The command ALL_SEND_CID and the fields and values for the MCI_CMDR Control Register
are described in Table 66 and Table 67.
Table 66. ALL_SEND_CID command description
Table 67. Fields and Values for MCI_CMDR Command Register
The MCI_ARGR contains the argument field of the command.
To send a command, the user must perform the following steps:
•
•
The command is sent immediately after writing the command register. The status bit
CMDRDY in the status register (MCI_SR) is asserted until the command is completed. If the
CMD
CMD Index
CMD2
Field
CMDNB (command number)
RSPTYP (response type)
SPCMD (special command)
OPCMD (open drain command)
MAXLAT (max latency for command to response)
TRCMD (transfer command)
TRDIR (transfer direction)
TRTYP (transfer type)
Fill the argument register (MCI_ARGR) with the command argument.
Set the command register (MCI_CMDR) (see Table 67).
S
T
Type
bcr
Host Command
Content
Argument
[31:0] stuff bits
CRC
E
Resp
R2
Z
N
ID
******
Cycles
Value
2 (CMD2)
2 (R2: 136 bits response)
0 (not a special command)
1
0 (NID cycles ==> 5 cycles)
0 (No transfer)
X (available only in transfer command)
X (available only in transfer command)
Abbreviation
ALL_SEND_CID
Z
S
T
Content
CID or OCR
AT91RM3400
Command Description
Asks all cards to send their
CID numbers on the CMD
line
Z
Z
377
Z
Related parts for AT91RM3400-DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: