AT91RM3400-DK Atmel, AT91RM3400-DK Datasheet - Page 43
AT91RM3400-DK
Manufacturer Part Number
AT91RM3400-DK
Description
KIT DEV FOR AT91RM3400
Manufacturer
Atmel
Series
AT91SAM Smart ARMr
Type
MCUr
Datasheets
1.AT91RM3400-DK.pdf
(461 pages)
2.AT91RM3400-DK.pdf
(2 pages)
3.AT91RM3400-DK.pdf
(25 pages)
Specifications of AT91RM3400-DK
Contents
Evaluation Board, Software and Documentation
Processor To Be Evaluated
AT91RM3400
Data Bus Width
32 bit
Interface Type
RS-232, USB
For Use With/related Products
AT91RM3400
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 43 of 461
- Download datasheet (6Mb)
Boot Program
Overview
1790A–ATARM–11/03
The Boot Program downloads an application in any of the AT91 products integrating a ROM. It
integrates a Bootloader and a boot Uploader to assure correct information download.
The Bootloader is activated first. It looks for a sequence of eight valid ARM exception vectors
in a DataFlash connected to the SPI, an EEPROM connected to the Two-wire Interface (TWI)
or an 8-bit memory device connected to the external bus interface (EBI) (if the device inte-
grates the EBI). All these vectors must be B-branch or LDR load register instructions except
for the sixth instruction. This vector is used to store information, such as the size of the image
to download and the type of DataFlash device.
If a valid sequence is found, code is downloaded into the internal SRAM. This is followed by a
remap and a jump to the first address of the SRAM.
If no valid ARM vector sequence is found, the boot Uploader is started. It initializes the Debug
Unit serial port (DBGU) and the USB Device Port. It then waits for any transaction and down-
loads a piece of code into the internal SRAM via a Device Firmware Upgrade (DFU) protocol
for USB and XMODEM protocol for the DBGU. After the end of the download, it branches to
the application entry point at the first address of the SRAM.
The main features of the Boot Program are:
•
•
•
•
•
•
•
•
Default Boot Program stored in ROM-based products
Downloads and runs an application from external storage media into internal SRAM
Downloaded code size depends on embedded SRAM size
Automatic detection of valid application
Bootloader supporting a wide range of non-volatile memories
–
–
–
Boot Uploader in case no valid program is detected in external NVM and supporting
several communication media
Serial communication on a DBGU (XModem protocol)
USB Device Port (DFU Protocol)
SPI DataFlash
Two-wire EEPROM
8-bit parallel memories on NCS0 (only for devices with EBI integrated)
®
connected on SPI NPCS0
AT91RM3400
43
Related parts for AT91RM3400-DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: