DV007004 Microchip Technology, DV007004 Datasheet - Page 63

• Manufacturer Part Number: DV007004
• Description: PROGRAMMER UNIVERSAL PM3
• Manufacturer: Microchip Technology
• Series: MPLAB&reg PM3r
• Type: Universalr

Specifications of DV007004

• Contents: MPLAB PM3 Programming Unit, Cables, Power Supply and IDE
• Positions/sockets: 1
• Ic Product Type: Programmer, Universal
• Supported Families: PICmicro, DsPIC30F
• Kit Contents: LCD, ICSP Support, 40-pin Socket, Digital/Multimedia Card Slot
• Rohs Compliant: NA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: Microchip's PICmicro devices including dsPIC30F
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With: PICmicro And DsPIC30F DSC Devices
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

7.4
© 2006 Microchip Technology Inc.
MPLAB PM3 PROGRAMMER MENU
Once the MPLAB PM3 programmer is selected, the full programmer menu displays (see
Table 7-3). The programmer must be enabled to make additional options available.
Some of the MPLAB PM3 options are accessible through the MPLAB PM3 Toolbar.
TABLE 7-3:
Select Programmer
Enable Programmer
Disable Programmer
Program
Verify
Read
Blank Check All
Blank Check OTP
Erase Flash Device
Reset Program Statistics
Transfer to MPLAB PM3
Transfer from MPLAB PM3
Establish
Communications
Load SQTP File
About
Environment
MPLAB PM3 Card
Settings
Selection
MPLAB
®
PM3 MENU
Lists the available programmers.
Enables the programmer.
Disables the programmer.
Transfers the hex data file to the programmer and programs the
device. Selective programming (e.g., part of program memory, or
only Configuration bits) can be configured with the “Programmer
Settings” option below.
Verifies that the device was programmed properly.
Reads the device content. Selective read (e.g., part of program
memory, only Configuration bits of the device) can be done by
setting up “Settings” below.
Checks that the device is completely blank (all bits are set to ‘1’).
This will also check that all Configuration bits are set to the
default value.
This function is intended for use with OTP devices that come
with factory programmed Configuration bits. Before using this
function, set the displayed Configuration bits to match the
factory programmed settings. The function verifies that all
program memory bits are set to ‘1’ and that the Configuration
bits match the settings displayed in the Configuration Bits dialog.
Erase all memory on a Flash device.
Resets the counters in the Program Statistics area.
Transfers the image of the MPLAB IDE’s memory to the
programmer, but does not program the device. This is useful for
stand-alone operation.
Transfers the image of the programmer’s memory to MPLAB
IDE, but does not read the device memory. This is useful for
reading back the memory after working in Stand-Alone mode.
Resets the programmer hardware and reestablishes
communications. Use this option if power has been
disconnected from the programmer. This option does not reset
programming information in the Program Memory window,
Configuration bits or IDs.
Allows the user to select a previously defined SQTP file. Refer to
Using SQTP.
Displays the OS Suite version of MPLAB PM3.
Displays a submenu of operations the can be performed on the
environment. See Chapter 9. “MPLAB PM3 Card Reference”
for more information on the environment operations.
Displays a submenu of operations that pertain to the MPLAB
PM3 Card. See Chapter 9. “MPLAB PM3 Card Reference” for
more information on the MPLAB PM3 Card operations.
Opens the Programmer dialog, which allows setting the memory
ranges and voltage specs, SQTP and communication ports.
Programmer options Program, Read, Verify, Transfer to MPLAB
PM3 and Transfer from MPLAB PM3 will be limited to these
settings until reset.
Description
DS51464C-page 57