SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 572

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

35.9.2
Name:
Address:
Access Type:
• CLKDIV: Clock Divider
Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK) divided by (2*(CLKDIV+1)).
• PWSDIV: Power Saving Divider
Multimedia Card Interface clock is divided by 2
Warning: This value must be different from 0 before enabling the Power Save Mode in the MCI_CR (MCI_PWSEN bit).
• RDPROOF Read Proof Enable
Enabling Read Proof allows to stop the MCI Clock during read access if the internal FIFO is full. This will guarantee data
integrity, not bandwidth.
0 = Disables Read Proof.
1 = Enables Read Proof.
• WRPROOF Write Proof Enable
Enabling Write Proof allows to stop the MCI Clock during write access if the internal FIFO is full. This will guarantee data
integrity, not bandwidth.
0 = Disables Write Proof.
1 = Enables Write Proof.
• PDCFBYTE: PDC Force Byte Transfer
Enabling PDC Force Byte Transfer allows the PDC to manage with internal byte transfers, so that transfer of blocks with a
size different from modulo 4 can be supported.
Warning: BLKLEN value depends on PDCFBYTE.
0 = Disables PDC Force Byte Transfer. PDC type of transfer are in words.
1 = Enables PDC Force Byte Transfer. PDC type of transfer are in bytes.
• PDCPADV: PDC Padding Value
0 = 0x00 value is used when padding data in write transfer (not only PDC transfer).
1 = 0xFF value is used when padding data in write transfer (not only PDC transfer).
574
PDCMODE
31
23
15
7
SAM9G10
MCI Mode Register
PDCPADV
30
22
14
MCI_MR
0xFFFA8004
Read/write
6
PDCFBYTE
29
21
13
5
(PWSDIV)
WRPROOF
28
20
12
4
+ 1 when entering Power Saving Mode.
BLKLEN
BLKLEN
CLKDIV
RDPROOF
27
19
11
3
26
18
10
2
PWSDIV
25
17
9
1
6462B–ATARM–6-Sep-11
24
16
8
0