SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 739

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

43. Revision History
6462B–ATARM–6-Sep-11
Doc. Rev.
6462B
Comments
Overview
Table 10-4, ”Multiplexing on PIO Controller C”
Boot Program
Section 13.7 ”NAND Flash
Chip ID
In
LCDC
Component changed from 6063K to 6385D.
PMC
Component version updated from 6066Q to 6066S.
SMC
2 variables updated: SMC_CYCLE and SMC_SETUP.
Table 22-5, ”Reset Values of Timing Parameters”
USART
An empty page and 2 empty bullets removed before
Electrical Characteristics
Table 39-1, ”Absolute Maximum
added Junction Temperature...+125°C.
Table 39-3, ”Power Consumption for Different
Table 39-5, ”Processor Clock Waveform
Table 39-6, ”Master Clock Waveform
Table 39-6, ”Master Clock Waveform
Section 39.10.1.1 ”Maximum SPI Frequency”
Table 39-25, ”SDRAM PC133
updated
Section 39.7 ”Core Power Supply POR Characteristics”
Figure titles within
Table 39-28, ”SPI Timings”
Errata
3 errata added:
Section 42.2.11.5 ”SSC: Data Sent Without Any Frame
on TD
Section 42.2.7.1 ”RSTC: Reset during SDRAM Accesses”
Section 42.2.5.3 ”MCI: Data Write Operation and Number of Bytes”
Document spellchecked to correct different typos.
Section 12.5.4 ”Debug
Output”, and
In the tables that follow, the most recent version of the document appears first.
Section 39.10.2.2 ”Timing Extraction”
Section 42.2.14.1 ”USART: Bad Value in Number of Errors
Unit”, chip ID value updated to 0x0199 03A1.
Boot”, 2 sentences added to the first paragraph.
updated: either Min or Max values kept.
Characteristics”, Data Out Access time after SDCK rising maximum value
Ratings*”, updated Operating Temperature (Industrial). -40°C to +85°C and
Parameters”, removed incomplete configuration for Master Clock.
Parameters”, t
Parameters”, removed incomplete configuration for Processor Clock.
added.
Modes”, updated Full Speed conditions & consumption.
updated: VDDIOP --> CDDIOM Power Supply for PC1 to 6.
and
CPPCK
Section 32.6.7 ”Test
Table 22-9, ”Register Mapping”
Synchro”,
added.
updated.
--> t
added.
CPMCK
Section 42.2.11.6 ”SSC: Unexpected Delay
added.
Modes”.
Register”.
updated.
SAM9G10
Change
Request
Ref.
6966
7643
6770
6866
7106
6742
rfo
7347
7355
7173
6732
6636
6872
7356
6467
7627
7703
rfo
741