PIC18C242-I/SP Microchip Technology, PIC18C242-I/SP Datasheet - Page 153

• Manufacturer Part Number: PIC18C242-I/SP
• Description: IC MCU OTP 8KX16 A/D 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C242-I/SP

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 22
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 23
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: MSSP, SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3DB18C452 - BOARD DAUGHTER ICEPIC3
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.1
The BRG supports both the Asynchronous and Syn-
chronous modes of the USART. It is a dedicated 8-bit
baud rate generator. The SPBRG register controls the
period of a free running 8-bit timer. In Asynchronous
mode, bit BRGH (TXSTA<2>) also controls the baud
rate. In Synchronous mode, bit BRGH is ignored.
Table 15-1 shows the formula for computation of the
baud rate for different USART modes, which only apply
in Master mode (internal clock).
Given the desired baud rate and F
integer value for the SPBRG register can be calculated
using the formula in Table 15-1. From this, the error in
baud rate can be determined.
EXAMPLE 15-1:
TABLE 15-1:
TABLE 15-2:
Legend: X = value in SPBRG (0 to 255)
TXSTA
RCSTA
SPBRG
Legend: x = unknown, - = unimplemented, read as '0'. Shaded cells are not used by the BRG.
Desired Baud Rate
Solving for X:
Calculated Baud Rate
Error
2001 Microchip Technology Inc.
Name
SYNC
0
1
USART Baud Rate Generator
(BRG)
X
X
X
Baud Rate Generator Register
CSRC
SPEN
Bit 7
BAUD RATE FORMULA
REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR
(Asynchronous) Baud Rate = F
(Synchronous) Baud Rate = F
CALCULATING BAUD RATE ERROR
Bit 6
TX9
RX9
=
=
=
=
=
=
=
=
=
BRGH = 0 (Low Speed)
SREN
TXEN
(Calculated Baud Rate - Desired Baud Rate)
F
( (F
((16000000 / 9600) / 64) - 1
[25.042] = 25
16000000 / (64 (25 + 1))
9615
(9615 - 9600) / 9600
0.16%
Bit 5
OSC
OSC
OSC
/ (64 (X + 1))
/ Desired Baud rate) / 64 ) - 1
, the nearest
CREN
SYNC
Desired Baud Rate
Bit 4
ADDEN
Bit 3
OSC
OSC
—
/(64(X+1))
/(4(X+1))
BRGH
FERR
Bit 2
Example 15-1 shows the calculation of the baud rate
error for the following conditions:
• F
• Desired Baud Rate = 9600
• BRGH = 0
• SYNC = 0
It may be advantageous to use the high baud rate
(BRGH = 1), even for slower baud clocks. This is
because the F
baud rate error in some cases.
Writing a new value to the SPBRG register causes the
BRG timer to be reset (or cleared). This ensures the
BRG does not wait for a timer overflow before output-
ting the new baud rate.
15.1.1
The data on the RC7/RX/DT pin is sampled three times
by a majority detect circuit to determine if a high or a
low level is present at the RX pin.
OSC
OERR
TRMT
Bit 1
= 16 MHz
SAMPLING
OSC
RX9D
TX9D
Bit 0
/(16(X + 1)) equation can reduce the
Baud Rate = F
BRGH = 1 (High Speed)
PIC18CXX2
0000 -010
0000 -00x
0000 0000
Value on
POR,
BOR
NA
OSC
DS39026C-page 151
/(16(X+1))
Value on all
0000 -010
0000 -00x
0000 0000
RESETS
other