PIC18C242-I/SP Microchip Technology, PIC18C242-I/SP Datasheet - Page 165

• Manufacturer Part Number: PIC18C242-I/SP
• Description: IC MCU OTP 8KX16 A/D 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C242-I/SP

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 22
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 23
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: MSSP, SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3DB18C452 - BOARD DAUGHTER ICEPIC3
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.4.2
The operation of the Synchronous Master and Slave
modes is identical, except in the case of the SLEEP
mode and bit SREN, which is a “don't care” in Slave
mode.
If receive is enabled by setting bit CREN prior to the
SLEEP instruction, then a word may be received during
SLEEP. On completely receiving the word, the RSR
register will transfer the data to the RCREG register,
and if enable bit RCIE bit is set, the interrupt generated
will wake the chip from SLEEP. If the global interrupt is
enabled, the program will branch to the interrupt vector.
TABLE 15-11: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
SPBRG
Legend: x = unknown, - = unimplemented, read as '0'.
Note 1: The PSPIF, PSPIE and PSPIP bits are reserved on the PIC18C2X2 devices. Always maintain these bits
2001 Microchip Technology Inc.
Name
Shaded cells are not used for Synchronous Slave Reception.
clear.
USART SYNCHRONOUS SLAVE
RECEPTION
USART Receive Register
Baud Rate Generator Register
PSPIE
PSPIP
PSPIF
CSRC
SPEN
GIEH
Bit 7
GIE/
(1)
(1)
(1)
PEIE/
GIEL
ADIF
ADIE
ADIP
Bit 6
RX9
TX9
TMR0IE INT0IE
SREN
TXEN
RCIE
RCIP
RCIF
Bit 5
CREN
SYNC
Bit 4
TXIF
TXIE
TXIP
ADDEN
SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
SSPIP CCP1IP TMR2IP TMR1IP 0000 0000 0000 0000
SSPIF
RBIE
Bit 3
—
TMR0IF INT0IF
CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
BRGH
FERR
Bit 2
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
To enable reception, set enable bit CREN.
Flag bit RCIF will be set when reception is com-
plete. An interrupt will be generated if enable bit
RCIE was set.
Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit CREN.
OERR
TRMT
Bit 1
RX9D
TX9D
RBIF
Bit 0
PIC18CXX2
0000 000x 0000 000u
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 -010 0000 -010
0000 0000 0000 0000
Value on
POR,
BOR
DS39026C-page 163
Value on
RESETS
all other