PIC18C242-I/SP Microchip Technology, PIC18C242-I/SP Datasheet - Page 54

• Manufacturer Part Number: PIC18C242-I/SP
• Description: IC MCU OTP 8KX16 A/D 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C242-I/SP

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 22
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 23
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: MSSP, SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3DB18C452 - BOARD DAUGHTER ICEPIC3
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18CXX2
4.13
The STATUS register, shown in Register 4-2, contains
the arithmetic status of the ALU. The STATUS register
can be the destination for any instruction, as with any
other register. If the STATUS register is the destination
for an instruction that affects the Z, DC, C, OV or N bits,
then the write to these five bits is disabled. These bits
are set or cleared according to the device logic. There-
fore, the result of an instruction with the STATUS regis-
ter as destination may be different than intended.
REGISTER 4-2:
DS39026C-page 52
STATUS Register
bit 7-5
bit 4
bit 3
bit 2
bit 1
bit 0
STATUS REGISTER
bit 7
Unimplemented: Read as '0'
N: Negative bit
This bit is used for signed arithmetic (2’s complement). It indicates whether the result was
negative, (ALU MSB = 1).
1 = Result was negative
0 = Result was positive
OV: Overflow bit
This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the 7-bit
magnitude, which causes the sign bit (bit7) to change state.
1 = Overflow occurred for signed arithmetic (in this arithmetic operation)
0 = No overflow occurred
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit carry/borrow bit
For ADDWF, ADDLW, SUBLW, and SUBWF instructions
1 = A carry-out from the 4th low order bit of the result occurred
0 = No carry-out from the 4th low order bit of the result
Note:
C: Carry/borrow bit
For ADDWF, ADDLW, SUBLW, and SUBWF instructions
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note:
Legend:
R = Readable bit
- n = Value at POR reset
U-0
—
For borrow, the polarity is reversed. A subtraction is executed by adding the two’s
complement of the second operand. For rotate (RRF, RLF) instructions, this bit is
loaded with either the bit 4 or bit 3 of the source register.
For borrow, the polarity is reversed. A subtraction is executed by adding the two’s
complement of the second operand. For rotate (RRF, RLF) instructions, this bit is
loaded with either the high or low order bit of the source register.
U-0
—
U-0
—
W = Writable bit
’1’ = Bit is set
R/W-x
N
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as 000u u1uu (where u = unchanged).
It is recommended, therefore, that only BCF, BSF,
SWAPF, MOVFF and MOVWF instructions are used to
alter the STATUS register, because these instructions
do not affect the Z, C, DC, OV or N bits from the
STATUS register. For other instructions not affecting
any status bits, see Table 19-2.
Note:
R/W-x
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
OV
The C and DC bits operate as a borrow and
digit borrow bit respectively, in subtraction.
R/W-x
Z
2001 Microchip Technology Inc.
x = Bit is unknown
R/W-x
DC
R/W-x
C
bit 0