MC68HC908JB8JPE Freescale Semiconductor, MC68HC908JB8JPE Datasheet - Page 143

• Manufacturer Part Number: MC68HC908JB8JPE
• Description: IC MCU FLASH 8BIT 8K 20-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908JB8JPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 3MHz
• Connectivity: USB
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Controller Family/series: HC08
• No. Of I/o's: 13
• Ram Memory Size: 256Byte
• Cpu Speed: 3MHz
• No. Of Timers: 1
• Embedded Interface Type: USB
• Rohs Compliant: Yes
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: USB
• Maximum Clock Frequency: 3 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 2
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

MC68HC908JB8•MC68HC08JB8•MC68HC08JT8 — Rev. 2.3
Freescale Semiconductor
TXD0F — Endpoint 0 Data Transmit Flag
RXD0F — Endpoint 0 Data Receive Flag
This read-only bit is set after the data stored in endpoint 0 transmit
buffers has been sent and an ACK handshake packet from the host is
received. Once the next set of data is ready in the transmit buffers,
software must clear this flag by writing a logic 1 to the TXD0FR bit. To
enable the next data packet transmission, TX0E also must be set. If
the TXD0F bit is not cleared, a NAK handshake will be returned in the
next IN transaction.
Reset clears this bit. Writing to TXD0F has no effect.
This read-only bit is set after the USB module has received a data
packet and responded with an ACK handshake packet. Software
must clear this flag by writing a logic 1 to the RXD0FR bit after all of
the received data has been read. Software also must set the RX0E bit
to 1 to enable the next data packet reception. If the RXD0F bit is not
cleared, the USB will respond with a NAK handshake to any
endpoint 0 OUT tokens; but does not respond to a SETUP token.
Reset clears this bit. Writing to RXD0F has no effect.
1 = Transmit on endpoint 0 has occurred
0 = Transmit on endpoint 0 has not occurred
1 = Receive on endpoint 0 has occurred
0 = Receive on endpoint 0 has not occurred
Universal Serial Bus Module (USB)
Universal Serial Bus Module (USB)
Technical Data
I/O Registers
143