MC9S08DZ128MLL Freescale Semiconductor, MC9S08DZ128MLL Datasheet - Page 204

• Manufacturer Part Number: MC9S08DZ128MLL
• Description: MCU 8BIT 128K FLASH 100-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08DZ128MLL

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 87
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-LQFP
• Processor Series: S08DZ
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 88
• Number Of Timers: 3
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• Controller Family/series: HCS08
• No. Of I/o's: 87
• Eeprom Memory Size: 2KB
• Ram Memory Size: 8KB
• Cpu Speed: 40MHz
• No. Of Timers: 3
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 9 Analog Comparator (S08ACMPV3)
9.3.1.1
ACMPxSC contains the status flag and control bits which are used to enable and configure the ACMP.
204
ACMOD
ACBGS
ACOPE
ACME
Field
ACIE
ACO
ACF
1:0
7
6
5
4
3
2
Reset:
W
R
Analog Comparator Module Enable — ACME enables the ACMP module.
0 ACMP not enabled
1 ACMP is enabled
Analog Comparator Bandgap Select — ACBGS is used to select between the bandgap reference voltage or
the ACMPx+ pin as the input to the non-inverting input of the analog comparatorr.
0 External pin ACMPx+ selected as non-inverting input to comparator
1 Internal reference select as non-inverting input to comparator
Note: refer to this chapter introduction to verify if any other config bits are necessary to enable the bandgap
Analog Comparator Flag — ACF is set when a compare event occurs. Compare events are defined by ACMOD.
ACF is cleared by writing a one to ACF.
0 Compare event has not occured
1 Compare event has occured
Analog Comparator Interrupt Enable — ACIE enables the interrupt from the ACMP. When ACIE is set, an
interupt will be asserted when ACF is set.
0 Interrupt disabled
1 Interrupt enabled
Analog Comparator Output — Reading ACO will return the current value of the analog comparator output. ACO
is reset to a 0 and will read as a 0 when the ACMP is disabled (ACME = 0).
Analog Comparator Output Pin Enable — ACOPE is used to enable the comparator output to be placed onto
the external pin, ACMPxO.
0 Analog comparator output not available on ACMPxO
1 Analog comparator output is driven out on ACMPxO
Analog Comparator Mode — ACMOD selects the type of compare event which sets ACF.
00 Encoding 0 — Comparator output falling edge
01 Encoding 1 — Comparator output rising edge
10 Encoding 2 — Comparator output falling edge
11 Encoding 3 — Comparator output rising or falling edge
ACMPx Status and Control Register (ACMPxSC)
reference in the chip level.
ACME
0
7
Table 9-2. ACMPx Status and Control Register Field Descriptions
= Unimplemented
ACBGS
Figure 9-3. ACMPx Status and Control Register
0
6
MC9S08DZ128 Series Data Sheet, Rev. 1
ACF
5
0
ACIE
0
4
Description
ACO
0
3
ACOPE
0
2
0
1
Freescale Semiconductor
ACMOD
0
0