MC9S08DZ128MLL Freescale Semiconductor, MC9S08DZ128MLL Datasheet - Page 69

• Manufacturer Part Number: MC9S08DZ128MLL
• Description: MCU 8BIT 128K FLASH 100-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08DZ128MLL

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 87
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-LQFP
• Processor Series: S08DZ
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 88
• Number Of Timers: 3
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• Controller Family/series: HCS08
• No. Of I/o's: 87
• Eeprom Memory Size: 2KB
• Ram Memory Size: 8KB
• Cpu Speed: 40MHz
• No. Of Timers: 3
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.6.4
The burst program command is used to program sequential bytes of data in less time than would be
required using the standard program command. This is possible because the high voltage to the FLASH
array does not need to be disabled between program operations. Ordinarily, when a program or erase
command is issued, an internal charge pump associated with the FLASH memory must be enabled to
supply high voltage to the array. Upon completion of the command, the charge pump is turned off. When
Freescale Semiconductor
4. Wait until the FCCF bit in FSTAT is set. As soon as FCCF= 1, the operation has completed
A strictly monitored procedure must be obeyed or the command will not be accepted. This
minimizes the possibility of any unintended changes to the memory contents. The command
complete flag (FCCF) indicates when a command is complete. The command sequence must be
completed by clearing FCBEF to launch the command.
of the commands except for burst programming and sector erase abort.
successfully.
Burst Program Execution
PROGRAM AND
ERASE FLOW
Figure 4-11. Program and Erase Flowchart
MC9S08DZ128 Series Data Sheet, Rev. 1
0
WRITE TO FLASH OR EEPROM TO
WRITE COMMAND TO FCMD
BUFFER ADDRESS AND DATA
TO LAUNCH COMMAND
AND CLEAR FCBEF
WRITE TO FCDIV
WRITE 1 TO FCBEF
CLEAR ERROR
FPVIOL OR
FACCERR?
FACCERR?
START
FCCF?
DONE
1
NO
(1)
(2)
Figure 4-11
0
YES
(2)
before checking FCBEF or FCCF.
(1)
Wait at least four bus cycles
after reset.
Required only once
ERROR EXIT
is a flowchart for executing all
Chapter 4 Memory
69