MC9S12C32CFAE16 Freescale Semiconductor, MC9S12C32CFAE16 Datasheet - Page 162

• Manufacturer Part Number: MC9S12C32CFAE16
• Description: IC MCU 32K FLASH 16MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C32CFAE16

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 16MHz
• Interface Type: CAN/SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 31
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/2.97V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: HCS12
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 2.5|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 31
• Number Of Timers: 8
• For Use With: CML12C32SLK - KIT STUDENT LEARNING 16BIT HCS12
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Chapter 5 Interrupt (INTV1) Block Description
5.4.1
The INT does not contain any user-controlled options for reducing power consumption. The operation of
the INT in low-power modes is discussed in the following subsections.
5.4.1.1
The INT does not contain any options for reducing power in run mode.
5.4.1.2
Clocks to the INT can be shut off during system wait mode and the asynchronous interrupt path will be
used to generate the wake-up signal upon recognition of a valid interrupt or any XIRQ request.
5.4.1.3
Clocks to the INT can be shut off during system stop mode and the asynchronous interrupt path will be
used to generate the wake-up signal upon recognition of a valid interrupt or any XIRQ request.
5.5
The INT supports three system reset exception request types: normal system reset or power-on-reset
request, crystal monitor reset request, and COP watchdog reset request. The type of reset exception request
must be decoded by the system and the proper request made to the core. The INT will then provide the
service routine address for the type of reset requested.
5.6
As shown in the block diagram in
and control, an optional highest priority I interrupt (HPRIO) block, and a priority decoder to evaluate
whether pending interrupts are valid and assess their priority.
5.6.1
The INT registers are accessible only in special modes of operation and function as described in
Section 5.3.2.1, “Interrupt Test Control
previously.
5.6.2
When the optional HPRIO block is implemented, the user is allowed to promote a single I-bit maskable
interrupt to be the highest priority I interrupt. The HPRIO evaluates all interrupt exception requests and
passes the HPRIO vector to the priority decoder if the highest priority I interrupt is active. RTI replaces
the promoted interrupt source.
162
Resets
Interrupts
Low-Power Modes
Interrupt Registers
Highest Priority I-Bit Maskable Interrupt
Operation in Run Mode
Operation in Wait Mode
Operation in Stop Mode
Figure
MC9S12C-Family / MC9S12GC-Family
Register,” and
5-1, the INT contains a register block to provide interrupt status
Rev 01.24
Section 5.3.2.2, “Interrupt Test
Freescale Semiconductor
Registers,”