MC9S12C32CFAE16 Freescale Semiconductor, MC9S12C32CFAE16 Datasheet - Page 433

• Manufacturer Part Number: MC9S12C32CFAE16
• Description: IC MCU 32K FLASH 16MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C32CFAE16

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 16MHz
• Interface Type: CAN/SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 31
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/2.97V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: HCS12
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 2.5|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 31
• Number Of Timers: 8
• For Use With: CML12C32SLK - KIT STUDENT LEARNING 16BIT HCS12
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

14.5
The reset values of registers and signals are described in the Memory Map and Registers section (see
Section 14.3, “Memory Map and Register
14.6
The SPIV3 only originates interrupt requests when SPI is enabled (SPE bit in SPICR1 set). The following
is a description of how the SPIV3 makes a request and how the MCU should acknowledge that request.
The interrupt vector offset and interrupt priority are chip dependent.
The interrupt flags MODF, SPIF and SPTEF are logically ORed to generate an interrupt request.
14.6.1
MODF occurs when the master detects an error on the SS pin. The master SPI must be configured for the
MODF feature (see
changed:
The MODF interrupt is reflected in the status register MODF flag. Clearing the flag will also clear the
interrupt. This interrupt will stay active while the MODF flag is set. MODF has an automatic clearing
process which is described in
14.6.2
SPIF occurs when new data has been received and copied to the SPI Data Register. After SPIF is set, it
does not clear until it is serviced. SPIF has an automatic clearing process which is described in
Section 14.3.2.4, “SPI Status Register (SPISR).”
of the next transfer (i.e. SPIF remains active throughout another transfer), the latter transfers will be
ignored and no new data will be copied into the SPIDR.
14.6.3
SPTEF occurs when the SPI Data Register is ready to accept new data. After SPTEF is set, it does not clear
until it is serviced. SPTEF has an automatic clearing process which is described in
Status Register (SPISR).”
Freescale Semiconductor
•
•
•
If a data transmission occurs in slave mode after reset without a write to SPIDR, it will transmit
garbage, or the byte last received from the master before the reset.
Reading from the SPIDR after reset will always read a byte of zeros.
MSTR = 0, The master bit in SPICR1 resets.
Reset
Interrupts
MODF
SPIF
SPTEF
Table
14-3). After MODF is set, the current transfer is aborted and the following bit is
Section 14.3.2.4, “SPI Status Register (SPISR).”
MC9S12C-Family / MC9S12GC-Family
Definition”) which details the registers and their bit-fields.
Rev 01.24
In the event that the SPIF is not serviced before the end
Chapter 14 Serial Peripheral Interface (SPIV3) Block Description
Section 14.3.2.4, “SPI
433