C8051F352 Silicon Laboratories Inc, C8051F352 Datasheet - Page 167

• Manufacturer Part Number: C8051F352
• Description: IC 8051 MCU 8K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F352

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x16b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: C8051F35x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• On-chip Dac: 8 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

20.
UART0 is an asynchronous, full duplex serial port offering modes 1 and 3 of the standard 8051 UART.
Enhanced baud rate support allows a wide range of clock sources to generate standard baud rates (details
in
to start reception of a second incoming data byte before software has finished reading the previous data
byte.
UART0 has two associated SFRs: Serial Control Register 0 (SCON0) and Serial Data Buffer 0 (SBUF0).
The single SBUF0 location provides access to both transmit and receive registers. Writes to SBUF0
always access the Transmit register. Reads of SBUF0 always access the buffered Receive register;
it is not possible to read data from the Transmit register.
With UART0 interrupts enabled, an interrupt is generated each time a transmit is completed (TI0 is set in
SCON0), or a data byte has been received (RI0 is set in SCON0). The UART0 interrupt flags are not
cleared by hardware when the CPU vectors to the interrupt service routine. They must be cleared manually
by software, allowing software to determine the cause of the UART0 interrupt (transmit complete or receive
complete).
Section “20.1. Enhanced Baud Rate Generation” on page
UART0
Rate Generator
UART Baud
Write to
SBUF
Figure 20.1. UART0 Block Diagram
Rx Clock
Tx Clock
Stop Bit
Start
Start
SBUF
Read
SCON
D
TB8
CLR
SET
Shift
Input Shift Register
Q
Shift
SFR Bus
(RX Latch)
Rx Control
(9 bits)
Tx Control
SBUF
0x1FF
SFR Bus
Zero Detector
(TX Shift)
SBUF
RB8
Load SBUF
Rev. 0.4
Tx IRQ
Rx IRQ
TI
RI
SBUF
Load
Send
Data
168). Received data buffering allows UART0
Interrupt
Serial
Port
TX
RX
C8051F350/1/2/3
Crossbar
Crossbar
Port I/O
167