R8A77850BDBGV#RD0Z Renesas Electronics America, R8A77850BDBGV#RD0Z Datasheet - Page 1198

• Manufacturer Part Number: R8A77850BDBGV#RD0Z
• Description: IC SUPERH MPU ROMLESS 436BGA
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7780r

Specifications of R8A77850BDBGV#RD0Z

• Core Processor: SH-4A
• Core Size: 32-Bit
• Speed: 600MHz
• Connectivity: Audio Codec, MMC, Serial Sound, SCI, SIO, SPI, SSI
• Peripherals: DMA, POR, WDT
• Number Of I /o: 108
• Program Memory Type: ROMless
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1 V ~ 1.2 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 436-BGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -

23. Serial Peripheral Interface (HSPI)
The HSPI_CS pin should be used to select the HSPI module and prepare it to receive data from an
external master when the HSPI is configured as a slave. When the FBS bit in SPCR is 0, the
HSPI_CS pin must be driven high between successive bytes (the HSPI_CS pin must be driven
high after a byte transfer). When FBS = 1, the HSPI_CS pin can stay low for several byte
transmissions. In this case, if the system is configured such that FBS is always 1, the HSPI_CS
line can be fixed at ground (if the HSPI will only be used as a slave).
23.4.2
In order to reduce the interrupt overhead on the CPU, FIFO mode has been provided. When FIFO
mode is enabled, up to eight bytes can be written in advance for transmission and up to eight bytes
can be received before the receive FIFO needs to be read. To transfer the specified amount of data
between the HSPI module and an external device, use the following procedure:
1. Set up the module for the required HSPI transfer characteristics (master/slave, clock polarity
2. Write bytes into the transmit FIFO via SPTBR. If more than eight bytes are to be transmitted,
3. Respond to the transmit FIFO halfway interrupt when it occurs by writing more data to the
4. When all of the transmit data has been written into the transmit FIFO, disable the transmit
5. Respond to the receive FIFO not empty interrupt until all the expected data has been received.
6. Disable the module until it is required again.
In some applications, an undefined amount of data will be received from an external HSPI device.
If this is the case, use the following procedure:
1. Set up the module for the required HSPI transfer characteristics (master/slave, clock polarity,
2. Fill the transmit FIFO with the data to transmit. Enable the receive FIFO not empty interrupt.
3. Respond to the receive FIFO not empty interrupt and read data from the receive FIFO until it is
4. Disable the module when the transfer is to stop.
Rev.1.00 Jan. 10, 2008 Page 1166 of 1658
REJ09B0261-0100
etc.) and enable FIFO mode.
enable the transmit FIFO halfway interrupt to keep track of the FIFO level as data is
transmitted.
transmit FIFO and reading data from the receive FIFO via SPRBR.
FIFO halfway interrupt and read the contents of the receive FIFO until it is empty. Enable the
receive FIFO not empty interrupt to keep track of when the final bytes of the transfer are
received.
etc.) and enable FIFO mode.
empty. Write more data to the transmit FIFO if required.
Operation with FIFO Mode Enabled