DK-DEV-4SGX530N Altera, DK-DEV-4SGX530N Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/0/40/altera_sml.jpg)
DK-DEV-4SGX530N
Manufacturer Part Number
DK-DEV-4SGX530N
Description
KIT DEVELOPMENT STRATIX IV
Manufacturer
Altera
Series
Stratix® IV GXr
Type
FPGAr
Datasheets
1.DK-DEV-4SGX530N.pdf
(57 pages)
2.DK-DEV-4SGX530N.pdf
(84 pages)
3.DK-DEV-4SGX530N.pdf
(1 pages)
Specifications of DK-DEV-4SGX530N
Contents
Board, Cable, Documentation, Power Supply
For Use With/related Products
Stratix® IV GX
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
544-2714
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Chapter 2: Board Components
Configuration, Status, and Setup Elements
Table 2–16. PCI Express Control DIP Switch Component Reference and Manufacturing Information
Table 2–17. Reset Configuration Push-Button Component Reference and Manufacturing Information
Table 2–18. Power Rail Measurements Based on the Rotary Switch Position (Part 1 of 2)
August 2010 Altera Corporation
SW5
S1
0
1
2
Board Reference
Board Reference
Switch
Schematic Signal Name
S4VCCIO_B7B8
Four-Position slide
DIP switch
Push-Button switch
S4VCC
3.3 V
Table 2–16
manufacturing information.
Reset Configuration Push-Button Switch
The reset configuration push-button switch, RESET_CONFIGn, is an input to the MAX II
CPLD EPM2210 System Controller. The push-button switch forces a reconfiguration
of the FPGA from flash memory. The location in the flash memory is based on the
input from the rotary switch position when the button is released. Valid locations
include 0 and 1 for the two pages in flash reserved for FPGA designs.
Table 2–17
manufacturing information.
Rotary Switch
The 16-position rotary switch (SW2) is wired to the MAX II CPLD EPM2210 System
Controller. This rotary switch serves the following purposes:
■
■
■
Table 2–18
Description
Description
At power up or when the reset configuration push-button switch (S1) is pressed,
this switch selects either the factory (page 0) or the user (page 1) design to load
into the FPGA.
After power up, the rotary switch selects the power rail monitored from among a
total of 16 rails. The power information is displayed in the Power GUI on a host PC
with a USB connection to the board.
User applications can obtain the switch value by reading the rsr register over the
FSM bus in the MAX II CPLD EPM2210 System Controller.
lists the power rails that are measured based on the rotary switch position.
lists the PCI Express control DIP switch component reference and
lists the reset configuration push-button switch component reference and
C & K Components
Voltage (V)
0.90
Panasonic Corporation
1.5
3.3
Manufacturer
Manufacturer
Device Pin
VCCIO_B7
VCCIO_B8
VCCHIP
VCC
—
TDA04H0SB1
Manufacturer
Stratix IV GX FPGA Development Board Reference Manual
Part Number
EVQPAC07K
Bank 7 I/O power (QDR2TOP0+DDR)
Bank 8 I/O power (QDR2TOP1+DDR)
FPGA core and periphery power
PCI Express hard IP block
All 3.3 V power to board (mA only)
Manufacturer
Part Number
Description
www.ck-components.com
Manufacturer Website
www.panasonic.com
Manufacturer
Website
2–19