ATTINY84V-10PU Atmel, ATTINY84V-10PU Datasheet - Page 153

• Manufacturer Part Number: ATTINY84V-10PU
• Description: AVR MCU, 8K FLASH, 512B RAM, 512B EE
• Manufacturer: Atmel

Specifications of ATTINY84V-10PU

• Controller Family/series: AVR Tiny
• No. Of I/o's: 12
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 10MHz
• Core Size: 8bit
• Program Memory Size: 8KB
• Oscillator Type: External, Internal
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Data Ram Size: 512 B
• Interface Type: SPI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-14
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18.10.2
8006F–AVR–02/07
ADCSRA – ADC Control and Status Register A
• Bit 7 – ADEN: ADC Enable
Writing this bit to one enables the ADC. By writing it to zero, the ADC is turned off. Turning the
ADC off while a conversion is in progress, will terminate this conversion.
• Bit 6 – ADSC: ADC Start Conversion
In Single Conversion mode, write this bit to one to start each conversion. In Free Running mode,
write this bit to one to start the first conversion. The first conversion after ADSC has been written
after the ADC has been enabled, or if ADSC is written at the same time as the ADC is enabled,
will take 25 ADC clock cycles instead of the normal 13. This first conversion performs initializa-
tion of the ADC.
ADSC will read as one as long as a conversion is in progress. When the conversion is complete,
it returns to zero. Writing zero to this bit has no effect.
• Bit 5 – ADATE: ADC Auto Trigger Enable
When this bit is written to one, Auto Triggering of the ADC is enabled. The ADC will start a con-
version on a positive edge of the selected trigger signal. The trigger source is selected by setting
the ADC Trigger Select bits, ADTS in ADCSRB.
• Bit 4 – ADIF: ADC Interrupt Flag
This bit is set when an ADC conversion completes and the data registers are updated. The ADC
Conversion Complete Interrupt is executed if the ADIE bit and the I-bit in SREG are set. ADIF is
cleared by hardware when executing the corresponding interrupt handling vector. Alternatively,
ADIF is cleared by writing a logical one to the flag. Beware that if doing a Read-Modify-Write on
ADCSRA, a pending interrupt can be disabled. This also applies if the SBI instruction is used.
• Bit 3 – ADIE: ADC Interrupt Enable
When this bit is written to one and the I-bit in SREG is set, the ADC Conversion Complete Inter-
rupt is activated.
• Bits 2:0 – ADPS2:0: ADC Prescaler Select Bits
These bits determine the division factor between the system clock frequency and the input clock
to the ADC.
Table 18-6.
Bit
0x06 (0x26)
Read/Write
Initial Value
ADPS2
0
0
0
0
1
ADC Prescaler Selections
ADEN
R/W
7
0
ADSC
R/W
ADPS1
6
0
0
0
1
1
0
ADATE
R/W
5
0
ADIF
R/W
4
0
ADPS0
0
1
0
1
0
ADIE
R/W
3
0
ADPS2
R/W
2
0
ATtiny24/44/84
ADPS1
R/W
Division Factor
1
0
16
2
2
4
8
ADPS0
R/W
0
0
ADCSRA
153