ATTINY84V-10PU Atmel, ATTINY84V-10PU Datasheet - Page 180

• Manufacturer Part Number: ATTINY84V-10PU
• Description: AVR MCU, 8K FLASH, 512B RAM, 512B EE
• Manufacturer: Atmel

Specifications of ATTINY84V-10PU

• Controller Family/series: AVR Tiny
• No. Of I/o's: 12
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 10MHz
• Core Size: 8bit
• Program Memory Size: 8KB
• Oscillator Type: External, Internal
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Data Ram Size: 512 B
• Interface Type: SPI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-14
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

DC Characteristics
Notes:
22.2
Figure 22-1. Maximum Frequency vs. V
180
Symbol
I
I
CC
ACLK
1. All DC Characteristics contained in this data sheet are based on simulation and characterization of other AVR microcontrol-
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (10 mA at V
5. Although each I/O port can source more than the test conditions (10 mA at V
Speed Grades
ATtiny24/44/84
lers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon.
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition. Pull up driving strenght of the PB3 RESET pad is weak.
Parameter
Power Supply Current
Power-down mode
Analog Comparator Input
Leakage Current
T
A
= -20°C to 85°C, V
10 MHz
20 MHZ
16 MHz
9,6 MHz
4 MHz
2 MHz
Condition
Active 1MHz, V
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
WDT disabled, V
V
V
CC
in
= V
CC
= 5V
CC
/2
CC
1.8V
= 1.8V to 5.5V (unless otherwise noted)
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
2.7V
Min.
-50
Safe Operating
4.5V
Area
CC
CC
= 5V, 5 mA at V
= 5V, 5 mA at V
Typ.
0.15
0.15
0.4
0.6
2.5
2
6
4
5.5V
(1)
(Continued)
CC
CC
= 3V) under steady state
Max.
10
50
1
= 3V) under steady state
8006F–AVR–02/07
Units
mA
mA
mA
mA
mA
mA
µA
µA
nA