ATTINY84V-10PU Atmel, ATTINY84V-10PU Datasheet - Page 69

• Manufacturer Part Number: ATTINY84V-10PU
• Description: AVR MCU, 8K FLASH, 512B RAM, 512B EE
• Manufacturer: Atmel

Specifications of ATTINY84V-10PU

• Controller Family/series: AVR Tiny
• No. Of I/o's: 12
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 10MHz
• Core Size: 8bit
• Program Memory Size: 8KB
• Oscillator Type: External, Internal
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Data Ram Size: 512 B
• Interface Type: SPI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-14
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8006F–AVR–02/07
• Port B, Bit 3 – RESET/dW/PCINT11
RESET: External Reset input is active low and enabled by unprogramming (“1”) the RSTDISBL
Fuse. Pullup is activated and output driver and digital input are deactivated when the pin is used
as the RESET pin.
dW: When the debugWIRE Enable (DWEN) Fuse is programmed and Lock bits are unpro-
grammed, the debugWIRE system within the target device is activated. The RESET port pin is
configured as a wire-AND (open-drain) bi-directional I/O pin with pull-up enabled and becomes
the communication gateway between target and emulator.
PCINT11: Pin Change Interrupt source 11. The PB3 pin can serve as an external interrupt
source for pin change interrupt 1.
Table 12-8 on page 69
overriding signals shown in
Table 12-8.
1.
2.
Signal
Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
PTOE
DIEOE
DIEOV
DI
AIO
RSTDISBL is 1 when the Fuse is “0” (Programmed).
DebugWIRE is enabled wheb DWEN Fuse is programmed and Lock bits are unprogrammed.
PB3/
PCINT11
RSTDISBL
1
RSTDISBL
DEBUGWIRE_ENABLE
Transmit
RSTDISBL
0
0
RSTDISBL
PCINT11 • PCIE1
DEBUGWIRE_ENABLE
PCINT11 • PCIE1)
dW/PCINT11 Input
Overriding Signals for Alternate Functions in PB3..PB2
RESET/dW/
(1)
(1)
(1)
(1)
and
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
Figure 12-5 on page
Table 12-9 on page 70
(2)
(2)
+ (RSTDISBL
• debugWire
(2)
(2)
(2)
(2)
(1)
62.
+
•
relate the alternate functions of Port B to the
PB2/INT0/OC0A/CKOUT/PCINT10
CKOUT
0
CKOUT
1'b1
CKOUT + OC0A enable
CKOUT • System Clock + CKOUT • OC0A
0
PCINT10 • PCIE1 + INT0
PCINT10 • PCIE1 + INT0
INT0/PCINT10 Input
ATtiny24/44/84
69