ATTINY84V-10PU Atmel, ATTINY84V-10PU Datasheet - Page 92

• Manufacturer Part Number: ATTINY84V-10PU
• Description: AVR MCU, 8K FLASH, 512B RAM, 512B EE
• Manufacturer: Atmel

Specifications of ATTINY84V-10PU

• Controller Family/series: AVR Tiny
• No. Of I/o's: 12
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 10MHz
• Core Size: 8bit
• Program Memory Size: 8KB
• Oscillator Type: External, Internal
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Data Ram Size: 512 B
• Interface Type: SPI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-14
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

14.2.1
92
ATtiny24/44/84
Registers
Figure 14-1. 16-bit Timer/Counter Block Diagram
Note:
The Timer/Counter (TCNT1), Output Compare Registers (OCR1A/B), and Input Capture Regis-
ter (ICR1) are all 16-bit registers. Special procedures must be followed when accessing the 16-
bit registers. These procedures are described in the section
page
access restrictions. Interrupt requests (abbreviated to Int.Req. in the figure) signals are all visible
in the Timer Interrupt Flag Register (TIFR). All interrupts are individually masked with the Timer
Interrupt Mask Register (TIMSK). TIFR and TIMSK are not shown in the figure.
The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on
the T1 pin. The Clock Select logic block controls which clock source and edge the Timer/Counter
uses to increment (or decrement) its value. The Timer/Counter is inactive when no clock source
is selected. The output from the Clock Select logic is referred to as the timer clock (clk
The double buffered Output Compare Registers (OCR1A/B) are compared with the
Timer/Counter value at all time. The result of the compare can be used by the Waveform Gener-
ator to generate a PWM or variable frequency output on the Output Compare pin (OC1A/B). See
”Output Compare Units” on page
Match Flag (OCF1A/B) which can be used to generate an Output Compare interrupt request.
94. The Timer/Counter Control Registers (TCCR1A/B) are 8-bit registers and have no CPU
1. See
Figure 1-1 on page 2
Timer/Counter
TCCRnA
OCRnA
OCRnB
TCNTn
ICRn
=
=
Direction
Count
Clear
for Timer/Counter1 pin placement and description.
100. The compare match event will also set the Compare
Control Logic
TOP
=
TCCRnB
Values
BOTTOM
Fixed
TOP
ICFn (Int.Req.)
(1)
clk
Detector
Edge
=
Tn
0
”Accessing 16-bit Registers” on
OCnA
(Int.Req.)
OCnB
(Int.Req.)
TOVn
(Int.Req.)
Clock Select
Generation
Generation
( From Prescaler )
Waveform
Waveform
Canceler
Detector
Noise
Edge
Comparator Ouput )
( From Analog
8006F–AVR–02/07
OCnA
OCnB
T
ICPn
1
Tn
).