N25Q128A11B1240E NUMONYX, N25Q128A11B1240E Datasheet - Page 115
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
N25Q128A11B1240E
Manufacturer Part Number
N25Q128A11B1240E
Description
Manufacturer
NUMONYX
Datasheet
1.N25Q128A11B1240E.pdf
(185 pages)
Specifications of N25Q128A11B1240E
Cell Type
NOR
Density
128Mb
Access Time (max)
7ns
Interface Type
Serial (SPI)
Boot Type
Bottom
Address Bus
1b
Operating Supply Voltage (typ)
1.8V
Operating Temp Range
-40C to 85C
Package Type
TBGA
Program/erase Volt (typ)
1.7 to 2/8.5 to 9.5V
Sync/async
Synchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
1.7V
Operating Supply Voltage (max)
2V
Word Size
8b
Number Of Words
16M
Supply Current
20mA
Mounting
Surface Mount
Pin Count
24
Lead Free Status / Rohs Status
Supplier Unconfirmed
- Current page: 115 of 185
- Download datasheet (6Mb)
9.2.1
DQ0
DQ1
S
C
1)
2)
Multiple I/O Read Identification protocol
The Multiple Input/Output Read Identification (MIORDID) instruction allows to read the
device identification data in the DIO-SPI protocol:
Unlike the RDID instruction of the Extended SPI protocol, the Multiple Input/Output
instruction can not read the Unique ID code (UID) (17 bytes).
For further details on the manufacturer and device identification codes please refer to
Section 9.1.1: Read Identification
Any Multiple Input/Output Read Identification (MIORDID) instruction while an Erase or
Program cycle is in progress, is not decoded, and has no effect on the cycle that is in
progress.
The device is first selected by driving Chip Select (S) Low. Then, the 8-bit instruction code
for the instruction is shifted in parallel on the 2 pins DQ0 and DQ1. After this, the 24-bit
device identification, stored in the memory, will be shifted out on again in parallel on DQ1
and DQ0. Each two bits are shifted out during the falling edge of Serial Clock (C).
The Read Identification (RDID) instruction is terminated by driving Chip Select (S) High at
any time during data output.
When Chip Select (S) is driven High, the device is put in the Standby Power mode. Once in
the Standby Power mode, the device waits to be selected, so that it can receive, decode and
execute instructions.
Figure 44. Multiple I/O Read Identification instruction and data-out sequence DIO-
The number of Dummy Clock cycles is configurable by the user
SSE is only available in devices with Bottom or Top architecture.
–
–
Manufacturer identification (1 byte)
Device identification (2 bytes)
SPI
0
1
AFh
2
3
7
6
4
5
4
MAN.
code
(RDID).
5
3
2
6
1
0
7
7
6
8
5
4
DEV.
code
9 10 11 12 13 14 15
3
2
1
0
7
6
SIZE
code
Dual_Multi_Read_IO
5
4
3
2
1
0
115/185
Related parts for N25Q128A11B1240E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![N25Q128](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
128-mbit 3 V, Multiple I/o, 4-kbyte Subsector Erase On Boot Sectors, Xip Enabled, Serial Flash Memory With 108 Mhz Spi Bus Interface
Manufacturer:
Numonyx
Datasheet:
![rc28f320j3d75d](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Numonyx Embedded Flash Memory J3 V. D
Manufacturer:
Numonyx
Datasheet:
![JS28F256M29EWH](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Manufacturer:
NUMONYX
Datasheet:
![JS28F640P33T85](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Manufacturer:
NUMONYX
Datasheet: