N25Q128A11B1240E NUMONYX, N25Q128A11B1240E Datasheet - Page 99
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
N25Q128A11B1240E
Manufacturer Part Number
N25Q128A11B1240E
Description
Manufacturer
NUMONYX
Datasheet
1.N25Q128A11B1240E.pdf
(185 pages)
Specifications of N25Q128A11B1240E
Cell Type
NOR
Density
128Mb
Access Time (max)
7ns
Interface Type
Serial (SPI)
Boot Type
Bottom
Address Bus
1b
Operating Supply Voltage (typ)
1.8V
Operating Temp Range
-40C to 85C
Package Type
TBGA
Program/erase Volt (typ)
1.7 to 2/8.5 to 9.5V
Sync/async
Synchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
1.7V
Operating Supply Voltage (max)
2V
Word Size
8b
Number Of Words
16M
Supply Current
20mA
Mounting
Surface Mount
Pin Count
24
Lead Free Status / Rohs Status
Supplier Unconfirmed
- Current page: 99 of 185
- Download datasheet (6Mb)
9.1.19
Figure 28. Sector Erase instruction sequence
Bulk Erase (BE)
The Bulk Erase (BE) instruction sets all bits to '1' (FFh). Before it can be accepted, a Write
Enable (WREN) instruction must previously have been executed. After the Write Enable
(WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL).
The Bulk Erase (BE) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code on Serial Data input (DQ0). Chip Select (S) must be driven Low for the
entire duration of the sequence.
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Bulk Erase instruction is not executed. As soon as Chip Select (S)
is driven High, the self-timed Bulk Erase cycle (whose duration is tBE) is initiated. While the
Bulk Erase cycle is in progress, the Status Register may be read to check the value of the
Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Bulk
Erase cycle, and is 0 when it is completed. At some unspecified time before the cycle is
completed, the Write Enable Latch (WEL) bit is reset.
The Bulk Erase (BE) instruction is executed only if all Block Protect (BP3, BP2, BP1, BP0)
bits are 0. The Bulk Erase (BE) instruction is ignored if one, or more, sectors are protected.
Figure 29. Bulk Erase instruction sequence
S
C
DQ0
S
C
DQ0
0
1
2
Instruction
3
0
4
1
5
2
6
Instruction
7
3
MSB
23 22
8
4
9
5
24 Bit Address
6
7
2
29 30 31
1
0
AI13743
Sector_Erase
99/185
Related parts for N25Q128A11B1240E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![N25Q128](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
128-mbit 3 V, Multiple I/o, 4-kbyte Subsector Erase On Boot Sectors, Xip Enabled, Serial Flash Memory With 108 Mhz Spi Bus Interface
Manufacturer:
Numonyx
Datasheet:
![rc28f320j3d75d](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Numonyx Embedded Flash Memory J3 V. D
Manufacturer:
Numonyx
Datasheet:
![JS28F256M29EWH](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Manufacturer:
NUMONYX
Datasheet:
![JS28F640P33T85](/images/manufacturer_photos/0/4/484/numonyx_tmb.jpg)
Part Number:
Description:
Manufacturer:
NUMONYX
Datasheet: