TMPM370FYDFG Toshiba, TMPM370FYDFG Datasheet - Page 108

• Manufacturer Part Number: TMPM370FYDFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 256K FLASH, 10K RAM
• Manufacturer: Toshiba

Specifications of TMPM370FYDFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 256K
• Rom Type: Flash
• Ram (kbytes): 10K
• Number Of Pins: 100
• Package: QFP(14x20)
• Vcc: 5V
• Cpu Mhz: 80
• Ssp (ch) Spi: -
• I2c/sio (ch): -
• Uart/sio (ch): 4
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 27
• 16-bit Timer / Counter: 8
• Motor / Igbt Control: Vector Engine
• Real Time Clock: -
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: -
• Hardware Cec Controller: -
• Comparators: 4
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit
• Lead Free Status / Rohs Status: Details

PEFR1
(0x4000_0108)
PEDATA
(0x4000_0100)
PECR
(0x4000_0104)
8.2.6
specified in units of bits. Besides the general-purpose input/output function, the port E performs the
serial interface function, timer input/output and the external interrupt input.
disabled.
and enable input in the PEIE register. These settings enable the interrupt input even if the
CGSTBYCR<DRVE> bit in the clock/mode control block is set to stop driving of pins during STOP
mode.
(Note)
The port E is a general-purpose, 8-bit input/output port. For this port, inputs and outputs can be
Reset initializes all bits of the port E as general-purpose ports with input, output, pull-up and pull-down
To use the external interrupt input for releasing STOP mode, select this function in the PEFR2 register
Port E (PE0 to PE7)
Bit Symbol
Read/Write
After reset
Function
Bit Symbol
Read/Write
After reset
Bit Symbol
Read/Write
After reset
Function
In modes other than STOP mode, interrupt input is enabled regardless of the PxFR
register setting as long as input is enabled in PxIE. Make sure to disable unused
interrupts when programming the device.
Type
0:PORT
1:TB3OUT.
PE7F1
PE7C
PE7
T14
7
0
7
7
7
0
0:PORT
1:TB3IN
PE6F1
PE6C
PE6
T12
Port E functions register 1
6
0
6
6
6
0
Port E control register
Port E circuit type
TMPM370 8-11
Port E register
0:PORT
1:TB2OUT
PE5F1
PE5C
PE5
T2
5
5
5
5
0
0
0:PORT
1: TB2IN
PE4F1
PE4C
PE4
T12
4
4
4
4
0
0
0: disabled
1: enabled
Output
R/W
R/W
R/W
“0”
0:PORT
1:TB4OUT
PE3F1
PE3C
PE3
T2
3
3
3
3
0
0
0:PORT
1:SCLK0
PE2F1
PE2C
PE2
T9
2
2
2
2
0
0
Input/Output Ports
0:PORT
1:RXD0
PE1F1
PE1C
PE1
T3
1
1
1
0
1
0
TMPM370
0:PORT
1: TXD0
PE0F1
PE0C
PE0
T2
0
0
0
0
0
0