M42800A Atmel Corporation, M42800A Datasheet - Page 193

• Manufacturer Part Number: M42800A
• Manufacturer: Atmel Corporation

Specifications of M42800A

• Flash (kbytes): 0 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 33 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 54
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3/5.0
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

19.12 SPI Status Register
Register Name:
Access Type:
Offset:
Reset Value:
• RDRF: Receive Data Register Full (Code Label SP_RDRF)
0 = No data has been received since the last read of SP_RDR
1= Data has been received and the received data has been transferred from the serializer to SP_RDR since the last read of
SP_RDR.
• TDRE: Transmit Data Register Empty (Code Label SP_TDRE)
0 = Data has been written to SP_TDR and not yet transferred to the serializer.
1 = The last data written in the Transmit Data Register has been transferred in the serializer.
TDRE equals zero when the SPI is disabled or at reset. The SPI enable command sets this bit to one.
• MODF: Mode Fault Error (Code Label SP_MODF)
0 = No Mode Fault has been detected since the last read of SP_SR.
1 = A Mode Fault occurred since the last read of the SP_SR.
• OVRES: Overrun Error Status (Code Label SP_OVRES)
0 = No overrun has been detected since the last read of SP_SR.
1 = An overrun has occurred since the last read of SP_SR.
An overrun occurs when SP_RDR is loaded at least twice from the serializer since the last read of the SP_RDR.
• SPENDRX: End of Receiver Transfer (Code Label SP_SPENDRX)
0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is inactive.
1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is active.
• SPENDTX: End of Transmitter Transfer (Code Label SP_SPENDTX)
0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is inactive.
1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is active.
• SPIENS: SPI Enable Status (Code Label SP_SPIENS)
0 = SPI is disabled.
1 = SPI is enabled.
1779D–ATARM–14-Apr-06
31
23
15
–
–
–
7
–
30
22
14
SP_SR
Read-only
0x10
0x0
–
–
–
6
–
SPENDTX
29
21
13
–
–
–
5
SPENDRX
28
20
12
–
–
–
4
OVRES
27
19
11
–
–
–
3
MODF
26
18
10
–
–
–
2
AT91M42800A
TDRE
25
17
–
–
9
–
1
SPIENS
RDRF
24
16
–
8
–
0
193