SAM7L128 Atmel Corporation, SAM7L128 Datasheet - Page 552

• Manufacturer Part Number: SAM7L128
• Manufacturer: Atmel Corporation

Specifications of SAM7L128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 36 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 80
• Ext Interrupts: 80
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 3
• Segment Lcd: 40
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 460
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 6
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.8 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

38.2
38.2.1
38.2.1.1
38.2.2
38.2.2.1
38.2.3
38.2.3.1
38.2.3.2
552
AT91SAM7L128/64
AT91SAM7L128/64 Preliminary
Analog-to-Digital Converter (ADC)
Pulse Width Modulation Controller (PWM)
Serial Peripheral Interface (SPI)
ADC: Sleep Mode
PWM: Counter Start Value
SPI: Baudrate Set to 1
SPI: Bad Serial Clock Generation on 2nd Chip Select
Refer to
If Sleep mode is activated while there is no activity (no conversion is being performed), it will
take effect only after a conversion occurs.
To activate sleep mode as soon as possible, it is recommended to write successively, ADC
Mode Register (SLEEP) then ADC Control Register (START bit field), in order to start an analog-
todigital conversion and then put ADC into sleep mode at the end of this conversion.
In left aligned mode, the first start value of the counter is 0. For the other periods, the counter
starts at 1.
None.
When the Baudrate is set at 1 (so, the serial clock frequency equals the master clock), and when
the BITS field (number of bits to be transmitted) in SPI_CSRx equals an odd value (in this case
9, 11, 13 or 15), an additional pulse will be generated on SPCK.
It does not occur when the BITS field is equal to 8, 10, 12, 14 or 16 and the Baudrate is equal
to 1.
None.
Bad Serial clock generation on the 2nd chip select when SCBR = 1, CPOL = 1 and NCPHA = 0.
This occurs using SPI with the following conditions:
Do not use a multiple Chip Select configuration where at least one SCRx register is configured
with SCBR = 1 and the others differ from 1 if NCPHA = 0 and CPOL = 1.
• Master Mode
• CPOL = 1 and NCPHA = 0
• Multiple chip selects are used with one transfer with Baud rate (SCBR) equal to 1 (i.e., when
• Transmitting with the slowest chip select and then with the fastest one, then an additional
serial clock frequency equals the system clock frequency) and the other transfers set with
SCBR are not equal to 1
pulse is generated on output SPCK during the second transfer.
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Section 38.1 “Marking” on page
551.
6257A–ATARM–20-Feb-08