SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 491

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
3. After the DMAC selected channel has been programmed, enable the channel by writing
4. Source and destination request single and chunk DMAC transactions to transfer the
5. When the buffer transfer has completed, the DMAC reloads the DMAC_SADDRx,
a. Write the starting source address in the DMAC_SADDRx register for channel x.
b. Write the starting destination address in the DMAC_DADDRx register for
c. Program DMAC_CTRLAx, DMAC_CTRLBx and DMAC_CFGx according to Row
d. Write the control information for the DMAC transfer in the DMAC_CTRLAx and
– i. Set up the transfer type (memory or non-memory peripheral for source and
– ii. Set up the transfer characteristics, such as:
e. If source picture-in-picture mode is enabled (DMAC_CTRLBx.SPIP is enabled),
f.
g. Write the channel configuration information into the DMAC_CFGx register for chan-
– i. Designate the handshaking interface type (hardware or software) for the source
– ii. If the hardware handshaking interface is activated for the source or destination
a ‘1’ to the DMAC_CHER.ENABLE[n] bit where is the channel number. Make sure that
bit 0 of the DMAC_EN register is enabled.
buffer of data (assuming non-memory peripherals). The DMAC acknowledges on com-
pletion of each chunk/single transaction and carry out the buffer transfer.
DMAC_DADDRx and DMAC_CTRLAx registers. Hardware sets the buffer Complete
interrupt. The DMAC then samples the row number as shown in
483. If the DMAC is in Row 1, then the DMAC transfer has completed. Hardware sets
the transfer complete interrupt and disables the channel. So you can either respond to
the Buffer Complete or Chained buffer transfer Complete interrupts, or poll for the
destination) and flow control device by programming the FC of the DMAC_CTRLBx
register.
and destination peripherals. This is not required for memory. This step requires
programming the SRC_H2SEL/DST_h2SEL bits, respectively. Writing a ‘1’ activates
the hardware handshaking interface to handle source/destination requests for the
specific channel. Writing a ‘0’ activates the software handshaking interface to handle
source/destination requests.
peripheral, assign handshaking interface to the source and destination peripheral.
This requires programming the SRC_PER and DST_PER bits, respectively.
– Transfer width for the source in the SRC_WIDTH field.
– Transfer width for the destination in the DST_WIDTH field.
– Source AHB master interface layer in the SIF field where source resides.
– Destination AHB master interface layer in the DIF field where destination resides.
– Incrementing/decrementing or fixed address for source in SRC_INCR field.
– Incrementing/decrementing or fixed address for destination in DST_INCR field.
channel x.
10 as shown in
‘0’.
DMAC_CTRLBx register for channel x. For example, in the register, you can pro-
gram the following:
program the DMAC_SPIPx register for channel x.
If destination picture-in-picture is enabled (DMAC_CTRLBx.DPIP), program the
DMAC_DPIPx register for channel x.
nel x. Ensure that the reload bits, DMAC_CFGx.SRC_REP,
DMAC_CFGx.DST_REP and DMAC_CTRLBx.AUTO are enabled.
Table 31-3 on page
483. Program the DMAC_DSCRx register with
Table 31-3 on page
SAM9G35
SAM9G35
491
491