SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 766

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

38.8.7
38.8.8
38.8.9
766
766
SAM9G35
SAM9G35
Using the DMA Controller (DMAC)
SMBUS Quick Command (Master Mode Only)
Read-write Flowcharts
Figure 38-13
the use of internal addresses to access the device.
Figure 38-13. Internal Address Usage
The use of the DMAC significantly reduces the CPU load.
To assure correct implementation, respect the following programming sequence.
The TWI interface can perform a Quick Command:
Figure 38-14. SMBUS Quick Command
The following flowcharts shown in
38-18 on page
read and write operations. A polling or interrupt method can be used to check the status bits.
The interrupt method requires that the interrupt enable register (TWI_IER) be configured first.
3. Program TWI_IADR with b3 b4 b5 b6 b7 b8 b9 b10 (b10 is the LSB of the 10-bit
1. Initialize the DMAC (channels, memory pointers, size, etc.);
1. Configure the master mode (DADR, CKDIV, etc.).
1. Enable the DMAC.
1. Wait for the DMAC flag.
1. Disable the DMAC.
1. Configure the master mode (DADR, CKDIV, etc.).
2. Write the MREAD bit in the TWI_MMR register at the value of the one-bit command to
3. Start the transfer by setting the QUICK bit in the TWI_CR.
address)
be sent.
below shows a byte write to an Atmel AT24LC512 EEPROM. This demonstrates
770,
R
S
T
A
T
M
S
B
Figure 38-19 on page 771
Address
Device
TXCOMP
0
Write QUICK command in TWI_CR
TXRDY
S
B
TWD
L
W
W
R
T
E
R
I
/
C
A
K
WORD ADDRESS
Figure 38-16 on page
M
S
B
S
FIRST
DADR
A
C
K
and
WORD ADDRESS
SECOND
Figure 38-20 on page 772
R/W
768,
L
S
B
C
A
K
A
Figure 38-17 on page
DATA
P
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
A
C
K
O
S
T
P
give examples for
769,
Figure