SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 832

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

39.7.5
39.7.5.1
832
832
SAM9G35
SAM9G35
IrDA Mode
IrDA Modulation
The USART features an IrDA mode supplying half-duplex point-to-point wireless communica-
tion. It embeds the modulator and demodulator which allows a glueless connection to the
infrared transceivers, as shown in
with the IrDA specification version 1.1 and support data transfer speeds ranging from 2.4 Kb/s to
115.2 Kb/s.
The USART IrDA mode is enabled by setting the USART_MODE field in the Mode Register
(US_MR) to the value 0x8. The IrDA Filter Register (US_IF) allows configuring the demodulator
filter. The USART transmitter and receiver operate in a normal asynchronous mode and all
parameters are accessible. Note that the modulator and the demodulator are activated.
Figure 39-32. Connection to IrDA Transceivers
The receiver and the transmitter must be enabled or disabled according to the direction of the
transmission to be managed.
To receive IrDA signals, the following needs to be done:
For baud rates up to and including 115.2 Kbits/sec, the RZI modulation scheme is used. “0” is
represented by a light pulse of 3/16th of a bit time. Some examples of signal pulse duration are
shown in
Table 39-12. IrDA Pulse Duration
Baud Rate
2.4 Kb/s
9.6 Kb/s
19.2 Kb/s
38.4 Kb/s
57.6 Kb/s
115.2 Kb/s
• Disable TX and Enable RX
• Configure the TXD pin as PIO and set it as an output to 0 (to avoid LED emission). Disable
• Receive data
the internal pull-up (better for power consumption).
Table
Transmitter
39-12.
Receiver
USART
Demodulator
Figure
Modulator
39-32. The modulator and demodulator are compliant
78.13 μs
19.53 μs
Pulse Duration (3/16)
9.77 μs
4.88 μs
3.26 μs
1.63 μs
RXD
TXD
RX
TX
Transceivers
IrDA
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11