SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 693

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

• SCBR: Serial Clock Baud Rate
In Master Mode, the SPI Interface uses a modulus counter to derive the SPCK baud rate from the Master Clock MCK. The
Baud rate is selected by writing a value from 1 to 255 in the SCBR field. The following equations determine the SPCK baud
rate:
Programming the SCBR field at 0 is forbidden. Triggering a transfer while SCBR is at 0 can lead to unpredictable results.
At reset, SCBR is 0 and the user has to program it at a valid value before performing the first transfer.
Note:
• DLYBS: Delay Before SPCK
This field defines the delay from NPCS valid to the first valid SPCK transition.
When DLYBS equals zero, the NPCS valid to SPCK transition is 1/2 the SPCK clock period.
Otherwise, the following equations determine the delay:
• DLYBCT: Delay Between Consecutive Transfers
This field defines the delay between two consecutive transfers with the same peripheral without removing the chip select.
The delay is always inserted after each transfer and before removing the chip select if needed.
When DLYBCT equals zero, no delay between consecutive transfers is inserted and the clock keeps its duty cycle over the
character transfers.
Otherwise, the following equation determines the delay:
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
Value
10
11
12
13
14
15
16
If one of the SCBR fields inSPI_CSRx is set to 1, the other SCBR fields in SPI_CSRx must be set to 1 as well, if they are
required to process transfers. If they are not used to transfer data, they can be set at any value.
7
8
Name
15_BIT
16_BIT
–
–
–
–
–
–
–
Delay Before SPCK
Delay Between Consecutive Transfers
SPCK Baudrate
=
Description
15 bits for transfer
16 bits for transfer
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
-------------- -
SCBR
MCK
=
DLYBS
------------------ -
MCK
=
32
----------------------------------- -
MCK
DLYBCT
SAM9G35
SAM9G35
693
693