AT32UC3C2512C Automotive Atmel Corporation, AT32UC3C2512C Automotive Datasheet - Page 432
AT32UC3C2512C Automotive
Manufacturer Part Number
AT32UC3C2512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 432 of 1312
- Download datasheet (20Mb)
22.4
22.4.1
22.4.2
22.4.3
22.4.4
22.5
22.5.1
22.5.2
9166C–AVR-08/11
Product Dependencies
Functional Description
Power Management
Clocks
Interrupt
Debug Operation
Enabling the SAU
Configuring the SAU Channels
In order to use this module, other parts of the system must be configured correctly, as described
below.
If the CPU enters a sleep mode that disables clocks used by the SAU, the SAU will stop func-
tioning and resume operation after the system wakes up from sleep mode.
The SAU has two bus clocks connected: One High Speed Bus clock (CLK_SAU_HSB) and one
Peripheral Bus clock (CLK_SAU_PB). These clocks are generated by the Power Manager. Both
clocks are enabled at reset, and can be disabled by writing to the Power Manager. The user has
to ensure that CLK_SAU_HSB is not turned off before accessing the SAU. Likewise, the user
must ensure that no bus access is pending in the SAU before disabling CLK_SAU_HSB. Failing
to do so may deadlock the High Speed Bus.
The SAU interrupt request line is connected to the interrupt controller. Using the SAU interrupt
requires the interrupt controller to be programmed first.
When an external debugger forces the CPU into debug mode, the SAU continues normal opera-
tion. If the SAU is configured in a way that requires it to be periodically serviced by the CPU
through interrupts or similar, improper operation or data loss may result during debugging.
The SAU is enabled by writing a one to the Enable (EN) bit in the Control Register (CR). This will
set the SAU Enabled (EN) bit in the Status Register (SR).
The SAU has a set of channels, mapped in the HSB memory space. These channels can be
configured by a Remap Target Register (RTR), located at the same memory address. When the
SAU is in normal mode, the SAU channel is addressed, and when the SAU is in setup mode, the
RTR can be addressed.
Before the SAU can be used, the channels must be configured and enabled. To configure a
channel, the corresponding RTR must be programmed with the Remap Target Address. To do
this, make sure the SAU is in setup mode by writing a one to the Setup Mode Enable (SEN) bit
in CR. This makes sure that a write to the RTR address accesses the RTR, not the SAU chan-
nel. Thereafter, the RTR is written with the address to remap to, typically the address of a
specific PB register. When all channels have been configured, return to normal mode by writing
a one to the Setup Mode Disable (SDIS) in CR. The channels can now be enabled by writing
ones to the corresponding bits in the Channel Enable Registers (CERH/L).
The SAU is only able to remap addresses above 0xFFFC0000.
AT32UC3C
432
Related parts for AT32UC3C2512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: