AT32UC3C2512C Automotive Atmel Corporation, AT32UC3C2512C Automotive Datasheet - Page 710
AT32UC3C2512C Automotive
Manufacturer Part Number
AT32UC3C2512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 710 of 1312
- Download datasheet (20Mb)
27.8.9.2
27.8.9.3
27.8.10
9166C–AVR-08/11
Identifying Bus Events
Timeouts
SMBus ALERT Signal
In combined transfers, the PECEN bit should only be written to one in the last of the combined
transfers. Consider the following transfer:
S, ADR+W, COMMAND_BYTE, ACK, SR, ADR+R, DATA_BYTE, ACK, PEC_BYTE, NACK, P
This transfer is generated by writing two commands to the command registers. The first com-
mand is a write with NBYTES=1 and PECEN=0, and the second is a read with NBYTES=2 and
PECEN=1.
Writing a one to the STOP bit in CR will place a STOP condition on the bus after the current
byte. No PEC byte will be sent in this case.
The TLOWS and TLOWM fields in SMBTR configure the SMBus timeout values. If a timeout
occurs, the master will transmit a STOP condition and leave the bus. A one is also written to the
SR.TOUT bit.
A slave can get the master’s attention by pulling the TWALM line low. A one will then be written
to SR.SMBAL. This can be set up to trigger an interrupt, and software can then take the appro-
priate action, as defined in the SMBus standard.
This chapter lists the different bus events, and how they affect bits in the TWIM registers. This is
intended to help writing drivers for the TWIM.
Table 27-5.
Event
Master transmitter has sent
a data byte
Master receiver has
received a data byte
Start+Sadr sent, no ack
received from slave
Data byte sent to slave, no
ack received from slave
Arbitration lost
SMBus Alert received
SMBus timeout received
Bus Events
Effect
SR.THR is cleared.
SR.RHR is set.
SR.ANAK is set.
SR.CCOMP not set.
CMDR.VALID remains set.
STOP automatically transmitted on bus.
SR.DNAK is set.
SR.CCOMP not set.
CMDR.VALID remains set.
STOP automatically transmitted on bus.
SR.ARBLST is set.
SR.CCOMP not set.
CMDR.VALID remains set.
TWCK and TWD immediately released to a pulled-up state.
SR.SMBAL is set.
SR.SMBTOUT is set.
SR.CCOMP not set.
CMDR.VALID remains set.
STOP automatically transmitted on bus.
AT32UC3C
710
Related parts for AT32UC3C2512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: