C505_9708 SIEMENS [Siemens Semiconductor Group], C505_9708 Datasheet - Page 199
C505_9708
Manufacturer Part Number
C505_9708
Description
8-Bit CMOS Microcontroller
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.C505_9708.pdf
(227 pages)
- Current page: 199 of 227
- Download datasheet (2Mb)
Power Saving Modes
C505 / C505C
9.2
Idle Mode
In the idle mode the oscillator of the C505 continues to run, but the CPU is gated off from the clock
signal. However, the interrupt system, the serial port, the A/D converter, the CAN controller (C505C
only), and all timers with the exception of the watchdog timer are further provided with the clock. The
CPU status is preserved in its entirety: the stack pointer, program counter, program status word,
accumulator, and all other registers maintain their data during idle mode.
The reduction of power consumption, which can be achieved by this feature depends on the number
of peripherals running. If all timers are stopped and the A/D converter, and the serial interfaces are
not running, the maximum power reduction can be achieved. This state is also the test condition for
the idle mode I
.
CC
Thus, the user has to take care which peripheral should continue to run and which has to be stopped
during idle mode. Also the state of all port pins – either the pins controlled by their latches or
controlled by their secondary functions – depends on the status of the controller when entering idle
mode.
Normally, the port pins hold the logical state they had at the time when the idle mode was activated.
If some pins are programmed to serve as alternate functions they still continue to output during idle
mode if the assigned function is on. This especially applies to the serial interface in case it cannot
finish reception or transmission during normal operation. The control signals ALE and PSEN are
held at logic high levels.
As in normal operation mode, the ports can be used as inputs during idle mode. Thus a capture or
reload operation can be triggered, the timers can be used to count external events, and external
interrupts will be detected.
The idle mode is a useful feature which makes it possible to "freeze" the processor's status - either
for a predefined time, or until an external event reverts the controller to normal operation, as
discussed below. The watchdog timer is the only peripheral which is automatically stopped during
idle mode.
Semiconductor Group
9-3
1997-08-01
Related parts for C505_9708
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Watts 28volts 200-450
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
50 WATTS - 28VOLTS 200-450 MHZ
Manufacturer:
ETC [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: