Z8F082A28100KIT ZILOG [Zilog, Inc.], Z8F082A28100KIT Datasheet - Page 110
Z8F082A28100KIT
Manufacturer Part Number
Z8F082A28100KIT
Description
Z8 Encore XP-R F08xA Series with eXtended Peripherals
Manufacturer
ZILOG [Zilog, Inc.]
Datasheet
1.Z8F082A28100KIT.pdf
(244 pages)
- Current page: 110 of 244
- Download datasheet (3Mb)
PS024705-0405
DE
1
0
1
0
Idle State
of Line
UART Interrupts
Figure 13.UART Driver Enable Signal Timing (shown with 1 Stop Bit and Parity)
⎛
⎝
------------------------------------ -
Baud Rate (Hz)
asserts at least one UART bit period and no greater than two UART bit periods before the
Start bit is transmitted. This allows a setup time to enable the transceiver. The Driver
Enable signal deasserts one system clock period after the final Stop bit is transmitted. This
one system clock delay allows both time for data to clear the transceiver before disabling
it, as well as the ability to determine if another character follows the current character. In
the event of back to back characters (new data must be written to the Transmit Data Regis-
ter before the previous character is completely transmitted) the DE signal is not deasserted
between characters. The Depol bit in the UART Control Register 1 sets the polarity of the
Driver Enable signal.
The Driver Enable to Start bit setup time is calculated as follows:
The UART features separate interrupts for the transmitter and the receiver. In addition,
when the UART primary functionality is disabled, the Baud Rate Generator can also func-
tion as a basic timer with interrupt capability.
Transmitter Interrupts
The transmitter generates a single interrupt when the Transmit Data Register Empty bit
(TDRE) is set to 1. This indicates that the transmitter is ready to accept new data for trans-
mission. The TDRE interrupt occurs after the Transmit shift register has shifted the first
bit of data out. The Transmit Data register can now be written with the next character to
send. This action provides 7 bit periods of latency to load the Transmit Data register
before the Transmit shift register completes shifting the current character. Writing to the
UART Transmit Data register clears the TDRE bit to 0.
Start
1
Bit0
lsb
Bit1
⎞
⎠
≤
DE to Start Bit Setup Time (s)
Bit2
P R E L I M I N A R Y
Bit3
Data Field
Bit4
Bit5
Bit6
Z8 Encore! XP
≤
⎛
⎝
------------------------------------ -
Baud Rate (Hz)
msb
Bit7
Product Specification
2
Parity
®
F08xA Seriess
Stop Bit
⎞
⎠
1
UART
92
Related parts for Z8F082A28100KIT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS Z8 consumer controller processor. ROM 4 KB, RAM 237 bytes, speed 12 MHz, 24 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS Z8 consumer controller processor. ROM 4 KB, RAM 236 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS Z8 consumer controller processor. ROM 4 KB, RAM 236 bytes, speed 12 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet: