S71GS128NB0 SPANSION [SPANSION], S71GS128NB0 Datasheet - Page 71
S71GS128NB0
Manufacturer Part Number
S71GS128NB0
Description
128N based MCPs
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S71GS128NB0.pdf
(195 pages)
- Current page: 71 of 195
- Download datasheet (3Mb)
December 15, 2004 S29GLxxxN_MCP_A1
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming
operation or a Write to Buffer programming operation so that data can be read
from any non-suspended sector. When the Program Suspend command is written
during a programming process, the device halts the program operation within 15
µs maximum (5µs typical) and updates the status bits. Addresses are not re-
quired when writing the Program Suspend command.
After the programming operation has been suspended, the system can read array
data from any non-suspended sector. The Program Suspend command may also
be issued during a programming operation while an erase is suspended. In this
case, data may be read from any addresses not in Erase Suspend or Program
Suspend. If a read is needed from the Secured Silicon Sector area (One-time Pro-
gram area), then user must use the proper command sequences to enter and exit
this region. Note that the Secured Silicon Sector autoselect, and CFI functions are
unavailable when program operation is in progress.
The system may also write the autoselect command sequence when the device
is in the Program Suspend mode. The system can read as many autoselect codes
as required. When the device exits the autoselect mode, the device reverts to the
Program Suspend mode, and is ready for another valid operation. See Autoselect
Command Sequence for more information.
A d v a n c e
Note:
Increment Address
See
S29GLxxxN MirrorBit
Figure 2. Program Operation
Table 12
I n f o r m a t i o n
Embedded
in progress
algorithm
Program
for program command sequence.
No
Command Sequence
TM
Flash Family
Write Program
Last Address?
Programming
from System
Verify Data?
Completed
Data Poll
START
Yes
Yes
No
71
Related parts for S71GS128NB0
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: