MC9S12C128CFUE Freescale Semiconductor, MC9S12C128CFUE Datasheet - Page 107

• Manufacturer Part Number: MC9S12C128CFUE
• Description: IC MCU 128K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C128CFUE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 25MHz
• Interface Type: CAN/SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 60
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/2.97V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: PQFP
• Processor Series: S12C
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 4000 B
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 61
• Number Of Timers: 1
• Operating Supply Voltage: - 0.3 V to + 6.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

A valid edge on input is detected if 4 consecutive samples of a passive level are followed by 4 consecutive
samples of an active level directly or indirectly.
The filters are continuously clocked by the bus clock in RUN and WAIT mode. In STOP mode the clock
is generated by a single RC oscillator in the Port Integration Module. To maximize current saving the RC
oscillator runs only if the following condition is true on any pin:
Sample count <= 4 and port interrupt enabled (PIE=1) and port interrupt flag not set (PIF=0).
2.4.2.6
In all modes, port J pins PJ[7:6] can be used for general purpose I/O or interrupt driven general purpose
I/O’s. During reset, port J pins are configured as inputs.
Port J offers 2 I/O ports with the same interrupt features as on port P.
2.4.3
All port and pin logic is located in the core module. Please refer to S12_mebi Block User Guide for details.
2.4.4
All ports start up as general purpose inputs on reset.
2.4.5
2.4.5.1
No low power options exist for this module in run mode.
2.4.5.2
No low power options exist for this module in wait mode.
2.4.5.3
All clocks are stopped. There are asynchronous paths to generate interrupts from STOP on port P and J.
2.5
The reset values of all registers are given in
2.5.1
All registers including the data registers get set/reset asynchronously.
properties after reset initialization.
Freescale Semiconductor
Initialization Information
Port A, B, E and BKGD Pin
External Pin Descriptions
Low Power Options
Reset Initialization
Port J
Run Mode
Wait Mode
Stop Mode
MC9S12C-Family / MC9S12GC-Family
Section 2.3.2, “Register
Rev 01.24
Chapter 2 Port Integration Module (PIM9C32) Block Description
Descriptions”.
Table 2-39
summarizes the port
107