MC9S12C64CFUE Freescale Semiconductor, MC9S12C64CFUE Datasheet - Page 299

• Manufacturer Part Number: MC9S12C64CFUE
• Description: IC MCU 64K FLASH 4K RAM 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C64CFUE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Processor Series: S12C
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 4 KB
• Interface Type: CAN/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 80PQFP
• Family Name: HCS12
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 2.5|5 V
• Height: 2.4 mm
• Length: 14 mm
• Supply Voltage (max): 2.75 V, 5.5 V
• Supply Voltage (min): 2.35 V, 2.97 V
• Width: 14 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The bit time is determined by the oscillator frequency, the baud rate prescaler, and the number of time
quanta (Tq) clock cycles per bit (as shown in
10.3.2.5
A flag can be cleared only by software (writing a 1 to the corresponding bit position) when the condition
which caused the setting is no longer valid. Every flag has an associated interrupt enable bit in the
CANRIER register.
Read: Anytime
Write: Anytime when out of initialization mode, except RSTAT[1:0] and TSTAT[1:0] flags which are read-
only; write of 1 clears flag; write of 0 is ignored.
1. The RSTAT[1:0], TSTAT[1:0] bits are not affected by initialization mode.
Freescale Semiconductor
Module Base + 0x0004
Reset:
W
R
1. This setting is not valid. Please refer to
MSCAN Receiver Flag Register (CANRFLG)
WUPIF
The CANRFLG register is held in the reset state
mode is active (INITRQ = 1 and INITAK = 1). This register is writable again
as soon as the initialization mode is exited (INITRQ = 0 and INITAK = 0).
TSEG13
Bit Time
0
7
0
0
0
0
1
1
:
Figure 10-8. MSCAN Receiver Flag Register (CANRFLG)
= Unimplemented
CSCIF
=
6
0
TSEG12
(
----------------------------------------------------- -
Prescaler value
0
0
0
0
1
1
:
f CANCLK
Table 10-8. Time Segment 1 Values
MC9S12C-Family / MC9S12GC-Family
RSTAT1
0
5
TSEG11
0
0
1
1
1
1
:
Table 10-7
Chapter 10 Freescale’s Scalable Controller Area Network (S12MSCANV2)
Table 10-34
Rev 01.24
NOTE
RSTAT0
)
•
4
0
(
1
TSEG10
+
and
TimeSegment1
0
1
0
1
0
1
:
for valid settings.
TSTAT1
Table
1
0
3
when the initialization
10-8).
1 Tq clock cycle
15 Tq clock cycles
16 Tq clock cycles
2 Tq clock cycles
3 Tq clock cycles
Time segment 1
4 Tq clock cycles
TSTAT0
2
0
+
TimeSegment2
:
(1)
OVRIF
1
1
0
1
)
Eqn. 10-1
RXF
0
0
299