ATTINY48-PU Atmel, ATTINY48-PU Datasheet - Page 44

• Manufacturer Part Number: ATTINY48-PU
• Description: MCU AVR 4K ISP FLASH 1.8V 28-DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY48-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 24
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 2-Wire/I2S/SPI
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 28
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit
• Package: 28PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 12 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.2.2
8.2.3
44
ATtiny48/88
External Reset
Brown-Out Detection
An External Reset is generated by a low level on the RESET pin. Reset pulses longer than the
minimum pulse width (see
running. Shorter pulses are not guaranteed to generate a reset. When the applied signal
reaches the Reset Threshold Voltage – V
MCU after the Time-out period – t
RSTDISBL fuse, see
Figure 8-4.
ATtiny48/88 has an On-chip Brown-out Detection (BOD) circuit for monitoring the V
ing operation by comparing it to a fixed trigger level. The trigger level for the BOD can be
selected by the BODLEVEL Fuses. The trigger level has a hysteresis to ensure spike free
Brown-out Detection. The hysteresis on the detection level should be interpreted as V
V
value below the trigger level (V
When V
MCU after the Time-out period t
The BOD circuit will only detect a drop in V
ger than t
Figure 8-5.
BOT
+ V
CC
HYST
BOD
CC
increases above the trigger level (V
/2 and V
given in
External Reset During Operation
Brown-out Reset During Operation
INTERNAL
TIME-OUT
RESET
RESET
V
CC
Table 20-4 on page
BOT-
“System and Reset Characterizations” on page
= V
Table 22-3 on page
BOT
BOT-
TOUT
TOUT
- V
in
HYST
has expired.
Figure
V
– has expired. The External Reset can be disabled by the
BOT-
/2. When the BOD is enabled, and V
RST
189.
CC
8-5), the Brown-out Reset is immediately activated.
– on its positive edge, the delay counter starts the
if the voltage stays below the trigger level for lon-
209) will generate a reset, even if the clock is not
BOT+
in
Figure
V
t
TOUT
8-5), the delay counter starts the
BOT+
209.
CC
decreases to a
8008G–AVR–04/11
CC
level dur-
BOT+
=