MC9S08QD4VSC Freescale Semiconductor, MC9S08QD4VSC Datasheet - Page 52

• Manufacturer Part Number: MC9S08QD4VSC
• Description: IC MCU 4K FLASH 256RAM 8-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QD4VSC

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: S08QD
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 4
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QD4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 256Byte
• # I/os (max): 4
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• For Use With: DEMO9S08QD4 - BOARD DEMO FOR MC9S08QD FAMILY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 5 Resets, Interrupts, and General System Control
5.4
The COP watchdog is intended to force a system reset when the application software fails to execute as
expected. To prevent a system reset from the COP timer (when it is enabled), application software must
reset the COP counter periodically. If the application program gets lost and fails to reset the COP counter
before it times out, a system reset is generated to force the system back to a known starting point.
After any reset, the COPE becomes set in SOPT1 enabling the COP watchdog (see
Options Register 2
application, it can be disabled by clearing COPE. The COP counter is reset by writing any value to the
address of SRS. This write does not affect the data in the read-only SRS. Instead, the act of writing to this
address is decoded and sends a reset signal to the COP counter.
The COPCLKS bit in SOPT2 (see
information) selects the clock source used for the COP timer. The clock source options are either the bus
clock or an internal 32 kHz clock source. With each clock source, there is an associated short and long
time-out controlled by COPT in SOPT1.
COPT bits. The COP watchdog defaults to operation from the 32 kHz clock source and the associated long
time-out (2
Even if the application will use the reset default settings of COPE, COPCLKS and COPT, the user must
write to the write-once SOPT1 and SOPT2 registers during reset initialization to lock in the settings. That
way, they cannot be changed accidentally if the application program gets lost. The initial writes to SOPT1
and SOPT2 will reset the COP counter.
The write to SRS that services (clears) the COP counter must not be placed in an interrupt service routine
(ISR) because the ISR could continue to be executed periodically even if the main application program
fails.
In Background debug mode, the COP counter will not increment.
When the bus clock source is selected, the COP counter does not increment while the system is in stop
mode. The COP counter resumes once the MCU exits stop mode.
When the 32 kHz clock source is selected, the COP counter is re-initialized to zero upon entry to stop
mode. The COP counter begins from zero once the MCU exits stop mode.
52
Computer Operating Properly (COP) Watchdog
8
cycles).
1
Values are shown in this column based on t
“Control
COPCLKS
(SOPT2),” for additional information). If the COP watchdog is not used in an
0
0
1
1
Timing,” for the tolerance of this value.
Control Bits
MC9S08QD4 Series MCU Data Sheet, Rev. 6
Table 5-1. COP Configuration Options
Section 5.8.5, “System Options Register 2
COPT
0
1
0
1
Table 5-1
Clock Source
summaries the control functions of the COPCLKS and
~32 kHz
~32 kHz
RTI
Bus
Bus
= 1 ms. See t
RTI
COP Overflow Count
2
2
13
10
in the
cycles (256 ms)
cycles (32 ms)
2
2
13
18
Section A.8.1,
cycles
cycles
(SOPT2),” for additional
Section 5.8.5, “System
1
Freescale Semiconductor
1