MC9S08QD4VSC Freescale Semiconductor, MC9S08QD4VSC Datasheet - Page 57

• Manufacturer Part Number: MC9S08QD4VSC
• Description: IC MCU 4K FLASH 256RAM 8-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QD4VSC

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: S08QD
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 4
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QD4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 256Byte
• # I/os (max): 4
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• For Use With: DEMO9S08QD4 - BOARD DEMO FOR MC9S08QD FAMILY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.6.1
When power is initially applied to the MCU, or when the supply voltage drops below the V
POR circuit will cause a reset condition. As the supply voltage rises, the LVD circuit will hold the MCU
in reset until the supply has risen above the V
following a POR.
5.6.2
The LVD can be configured to generate a reset upon detection of a low voltage condition by setting
LVDRE to 1. After an LVD reset has occurred, the LVD system will hold the MCU in reset until the supply
voltage has risen above the level determined by LVDV. The LVD bit in the SRS register is set following
either an LVD reset or POR.
5.6.3
When a low voltage condition is detected and the LVD circuit is configured using SPMSC1 for interrupt
operation (LVDE set, LVDIE set, and LVDRE clear), then LVDF in SPMSC1 will be set and an LVD
interrupt request will occur.
5.6.4
The LVD system has a low voltage warning flag to indicate to the user that the supply voltage is
approaching, but is above, the LVD voltage. The LVW does not have an interrupt associated with it. There
are two user selectable trip voltages for the LVW, one high (V
voltage is selected by LVWV in SPMSC2.
5.7
The real-time interrupt function can be used to generate periodic interrupts. The RTI can accept two
sources of clocks, the 1 kHz internal clock or an 32 kHz ICS clock if available. The RTICLKS bit in
SRTISC is used to select the RTI clock source.
Both clock source can be used when the MCU is in run, wait or stop3 mode. When using the 32 kHz ICS
clock in stop3, it must be enabled in stop (EREFSTEN = 1) and configured for low frequency operation
(RANGE = 0). Only the internal 1 kHz clock source can be selected to wake the MCU from stop1 or stop2
modes.
The SRTISC register includes a read-only status flag, a write-only acknowledge bit, and a 3-bit control
value (RTIS) used to select one of seven wakeup periods. The RTI has a local interrupt enable, RTIE, to
allow masking of the real-time interrupt. The RTI can be disabled by writing each bit of RTIS to zeroes,
and no interrupts will be generated. See
Register
Freescale Semiconductor
(SRTISC),” for detailed information about this register.
Real-Time Interrupt (RTI)
Power-On Reset Operation
LVD Reset Operation
LVD Interrupt Operation
Low-Voltage Warning (LVW)
MC9S08QD4 Series MCU Data Sheet, Rev. 6
Section 5.8.7, “System Real-Time Interrupt Status and Control
LVDL
level. Both the POR bit and the LVD bit in SRS are set
Chapter 5 Resets, Interrupts, and General System Control
LVWH
) and one low (V
LVWL
). The trip
POR
level, the
57