DF70845AD80FPV Renesas Electronics America, DF70845AD80FPV Datasheet - Page 179

• Manufacturer Part Number: DF70845AD80FPV
• Description: IC SUPERH MCU FLASH 112LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7080r

Specifications of DF70845AD80FPV

• Core Size: 32-Bit
• Program Memory Size: 512KB (512K x 8)
• Core Processor: SH-2
• Speed: 80MHz
• Connectivity: EBI/EMI, FIFO, I²C, SCI, SSU
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 76
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V, 4.5V To 5.5V
• Embedded Interface Type: I2C, SCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K570865S001BE - KIT STARTER FOR SH7086R0K570865S000BE - KIT STARTER FOR SH7086HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

6.4
6.4.1
There are four types of interrupt sources: User break, NMI, IRQ, and on-chip peripheral modules.
Individual interrupts are given priority levels (0 to 16, with 0 the lowest and 16 the highest).
Giving an interrupt a priority level of 0 masks it.
NMI Interrupt: The NMI interrupt is given a priority level of 16 and is always accepted. An NMI
interrupt is detected at the edge of the pins. Use the NMI edge select bit (NMIE) in interrupt
control register 0 (ICR0) to select either the rising or falling edge. In the NMI interrupt exception
handler, the interrupt mask level bits (I3 to I0) in the status register (SR) are set to level 15.
IRQ7 to IRQ0 Interrupts: IRQ interrupts are requested by input from pins IRQ0 to IRQ7. Use
the IRQ sense select bits (IRQ71S to IRQ 01S and IRQ70S to IRQ00S) in the IRQ control register
(IRQCR) to select the detection mode from low level detection, falling edge detection, rising edge
detection, and both edge detection for each pin. The priority level can be set from 0 to 15 for each
pin using the interrupt priority registers A and B (IPRA and IPRB).
In the case that the low level detection is selected, an interrupt request signal is sent to the INTC
while the IRQ pin is driven low. The interrupt request signal stops to be sent to the INTC when the
IRQ pin becomes high. It is possible to confirm that an interrupt is requested by reading the IRQ
flags (IRQ7F to IRQ0F) in the IRQ status register (IRQSR).
In the case that the edge detection is selected, an interrupt request signal is sent to the INTC when
the following change on the IRQ pin is detected: from high to low in falling edge detection mode,
from low to high in rising edge detection mode, and from low to high or from high to low in both
edge detection mode. The IRQ interrupt request by detecting the change on the pin is held until the
interrupt request is accepted. It is possible to confirm that an IRQ interrupt request has been
detected by reading the IRQ flags (IRQ7F to IRQ0F) in the IRQ status register (IRQSR). An IRQ
interrupt request by detecting the change on the pin can be withdrawn by writing 0 to an IRQ flag
after reading 1.
In the IRQ interrupt exception handling, the interrupt mask bits (I3 to I0) in the status register
(SR) are set to the priority level value of the accepted IRQ interrupt. Figure 6.2 shows the block
diagram of the IRQ7 to IRQ0 interrupts.
Interrupt Sources
External Interrupts
Rev. 3.00 May 17, 2007 Page 121 of 1582
Section 6 Interrupt Controller (INTC)
REJ09B0181-0300