ST72F344K4T6 STMicroelectronics, ST72F344K4T6 Datasheet - Page 103

• Manufacturer Part Number: ST72F344K4T6
• Description: MCU 8BIT 16KB FLASH MEM 32-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F344K4T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST72F34X-SK/RAIS, ST7MDT40-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: 497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-5611

ST72344xx ST72345xx
One-pulse mode
One-pulse mode enables the generation of a pulse when an external event occurs. This
mode is selected via the OPM bit in the CR2 register.
The one-pulse mode uses the Input Capture1 function and the Output Compare1 function.
Procedure:
To use one-pulse mode:
1.
2.
3.
Figure 52. One-pulse mode cycle
When a valid event occurs on the ICAP1 pin, the counter value is loaded in the ICR1
register. The counter is then initialized to FFFCh, the OLVL2 bit is output on the OCMP1 pin
and the ICF1 bit is set.
Because the ICF1 bit is set when an active edge occurs, an interrupt can be generated if the
ICIE bit is set.
Clearing the Input Capture interrupt request (i.e. clearing the ICFi bit) is done in two steps:
1.
2.
Load the OC1R register with the value corresponding to the length of the pulse (see the
formula in the opposite column).
Select the following in the CR1 register:
–
–
–
Select the following in the CR2 register:
–
–
–
Reading the SR register while the ICFi bit is set.
An access (read or write) to the ICiLR register.
Using the OLVL1 bit, select the level to be applied to the OCMP1 pin after the
pulse.
Using the OLVL2 bit, select the level to be applied to the OCMP1 pin during the
pulse.
Select the edge of the active transition on the ICAP1 pin with the IEDG1 bit (the
ICAP1 pin must be configured as floating input).
Set the OC1E bit, the OCMP1 pin is then dedicated to the Output Compare 1
function.
Set the OPM bit.
Select the timer clock CC[1:0] (see
event occurs
on ICAP1
Doc ID 12321 Rev 5
Counter
= OC1R
When
When
One-pulse mode cycle
Table 50: Clock control bits on page
OCMP1 = OLVL2
OCMP1 = OLVL1
Counter is reset
ICR1 = Counter
ICF1 bit is set
to FFFCh
On-chip peripherals
110).
103/247