MCF5280CVM66 Freescale Semiconductor, MCF5280CVM66 Datasheet - Page 144

• Manufacturer Part Number: MCF5280CVM66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5280CVM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• No. Of I/o's: 150
• Program Memory Size: 2KB
• Ram Memory Size: 64KB
• Cpu Speed: 66.67MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

Power Management
7.3.2.8
In wait and doze modes, the UART may generate an interrupt to exit the low-power modes.
In stop mode, the UARTs stop immediately and freeze their operation, register values, state machines, and
external pins. During this mode, the UART clocks are shut down. Coming out of stop mode returns the
UARTs to operation from the state prior to the low-power mode entry.
7.3.2.9
When the I
mode, the I
mode. For an interrupt to occur, the I2CR[IIE] bit must be set to enable interrupts, and the setting of the
I2SR[IIF] generates the interrupt signal to the CPU and interrupt controller. The setting of I2SR[IIF]
signifies either the completion of one byte transfer or the reception of a calling address matching its own
specified address when in slave receive mode.
In stop mode, the I
Upon exiting stop mode, the I
7.3.2.10 Queued Serial Peripheral Interface (QSPI)
In wait and doze modes, the queued serial peripheral interface (QSPI) may generate an interrupt to exit the
low-power modes.
In stop mode, the QSPI stops immediately and freezes operation, register values, state machines, and
external pins. During this mode, the QSPI clocks are shut down. Coming out of stop mode returns the QSPI
to operation from the state prior to the low-power mode entry.
7.3.2.11 DMA Timers (DMAT0–DMAT3)
In wait and doze modes, the DMA timers may generate an interrupt to exit a low-power mode. This
interrupt can be generated when the DMA Timer is in either input capture mode or reference compare
mode.
In input capture mode, where the capture enable (CE) field of the timer mode register (DTMR) has a
non-zero value and the DMA enable (DMAEN) bit of the DMA timer extended mode register (DTXMR)
is cleared, an interrupt is issued upon a captured input. In reference compare mode, where the output
reference request interrupt enable (ORRI) bit of DTMR is set and the DTXMR[DMAEN] bit is cleared,
an interrupt is issued when the timer counter reaches the reference value.
DMA timer operation is disabled in stop mode, but the DMA timer is unaffected by either the wait or doze
modes and may generate an interrupt to exit these modes. Upon exiting stop mode, the timer will resume
operation unless stop mode was exited by reset.
7-8
•
•
•
•
Clearing the transmit enable bit (TE) or the receiver enable bit (RE) disables UART functions.
The UARTs are unaffected by wait mode and may generate an interrupt to exit this mode.
Clearing the QSPI enable bit (SPE) disables the QSPI function.
The QSPI is unaffected by wait mode and may generate an interrupt to exit this mode.
2
2
C Module is enabled by the setting of the I2CR[IEN] bit and when the device is not in stop
UART Modules (UART0, UART1, and UART2)
I
C module is operable and may generate an interrupt to bring the device out of a low-power
2
C Module
2
C Module stops immediately and freezes operation, register values, and external pins.
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
2
C resumes operation unless stop mode was exited by reset.
Freescale Semiconductor