AT90USB647-MU Atmel, AT90USB647-MU Datasheet - Page 399

• Manufacturer Part Number: AT90USB647-MU
• Description: MCU, 8BIT, 64K FLASH, USB, 64QFN
• Manufacturer: Atmel

Specifications of AT90USB647-MU

• Controller Family/series: AT90
• No. Of I/o's: 48
• Eeprom Memory Size: 2KB
• Ram Memory Size: 4KB
• Cpu Speed: 16MHz
• No. Of: RoHS Compliant
• Core Size: 8bit
• Program Memory Size: 64KB
• Oscillator Type: External, Internal
• Package: 64QFN EP
• Device Core: AVR
• Family Name: AT90
• Maximum Speed: 20 MHz
• Ram Size: 4 KB
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 48
• Interface Type: SPI/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Operating Temperature: -40 to 85 °C
• Number Of Timers: 4
• Lead Free Status / Rohs Status: Details

T
Note:
7593K–AVR–11/09
A
Symbol
I
Icc
V
I
t
Iq
Vusb
CC
ACLK
ACID
ACIO
= -40°C to 85°C, V
1. "Max" means the highest value where the pin is guaranteed to be read as low
2. "Min" means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady state
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
5. All DC Characteristics contained in this datasheet are based on simulation and characterization of other AVR microcon-
6. Values with “Power Reduction Register 1 - PRR1” disabled (0x00).
conditions (non-transient), the following must be observed:
AT90USB64/128:
1.)The sum of all IOL, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2.)The sum of all IOL, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3.)The sum of all IOL, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4.)The sum of all IOL, for ports F0-F7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
AT90USB64/128:
1)The sum of all IOH, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2)The sum of all IOH, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3)The sum of all IOH, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4)The sum of all IOH, for ports F0-F7 should not exceed 100 mA.
trollers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
USB Regulator Quiescent
Current
USB Regulator Output
Voltage (Ucap)
CC
= 2.7V to 5.5V (unless otherwise noted) (Continued)
(6)
(AT90USB64/128)
Active 8MHz, V
(AT90USB64/128)
Active 8MHz, V
(AT90USB64/128)
Active 16MHz, V
V
V
V
Condition
Active 4MHz, V
(AT90USB64/128)
WDT enabled, BOD
enabled, V
WDT enabled, BOD
disabled, V
WDT disabled, BOD
disabled, V
V
V
V
UVcc > 3.6V, I = 0mA
UVcc > 3.6V, I = 40mA
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
= 3V, 25°C
= 3V, 25°C
= 3V, 25°C
CC
CC
CC
CC
= 3V
= 3V
= 5V
= 5V
(8)
Min.
-50
3.0
(5)
Typ.
750
500
2.5
3.3
10
19
30
10
10
10
5
2
AT90USB64/128
Max.
3.5
10
18
30
40
50
30
5
(5)
Units
mA
mA
mA
mA
mV
µA
µA
µA
nA
µA
ns
V
399