AT90USB647-MU Atmel, AT90USB647-MU Datasheet - Page 76

• Manufacturer Part Number: AT90USB647-MU
• Description: MCU, 8BIT, 64K FLASH, USB, 64QFN
• Manufacturer: Atmel

Specifications of AT90USB647-MU

• Controller Family/series: AT90
• No. Of I/o's: 48
• Eeprom Memory Size: 2KB
• Ram Memory Size: 4KB
• Cpu Speed: 16MHz
• No. Of: RoHS Compliant
• Core Size: 8bit
• Program Memory Size: 64KB
• Oscillator Type: External, Internal
• Package: 64QFN EP
• Device Core: AVR
• Family Name: AT90
• Maximum Speed: 20 MHz
• Ram Size: 4 KB
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 48
• Interface Type: SPI/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Operating Temperature: -40 to 85 °C
• Number Of Timers: 4
• Lead Free Status / Rohs Status: Details

10.2.5
10.2.6
76
AT90USB64/128
Digital Input Enable and Sleep Modes
Unconnected Pins
Note:
As shown in
schmitt-trigger. The signal denoted SLEEP in the figure, is set by the MCU Sleep Controller in
Power-down mode, Power-save mode, and Standby mode to avoid high power consumption if
some input signals are left floating, or have an analog signal level close to V
SLEEP is overridden for port pins enabled as external interrupt pins. If the external interrupt
request is not enabled, SLEEP is active also for these pins. SLEEP is also overridden by various
other alternate functions as described in
If a logic high level (“one”) is present on an asynchronous external interrupt pin configured as
“Interrupt on Rising Edge, Falling Edge, or Any Logic Change on Pin” while the external interrupt
is not enabled, the corresponding External Interrupt Flag will be set when resuming from the
above mentioned Sleep mode, as the clamping in these sleep mode produces the requested
logic change.
If some pins are unused, it is recommended to ensure that these pins have a defined level. Even
though most of the digital inputs are disabled in the deep sleep modes as described above, float-
Assembly Code Example
C Code Example
unsigned char i;
...
; Define pull-ups and set outputs high
; Define directions for port pins
ldi
ldi
out
out
; Insert nop for synchronization
nop
; Read port pins
in
...
...
/* Define pull-ups and set outputs high */
/* Define directions for port pins */
PORTB = (1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0);
DDRB = (1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0);
/* Insert nop for synchronization*/
__no_operation();
/* Read port pins */
i = PINB;
...
1. For the assembly program, two temporary registers are used to minimize the time from pull-
ups are set on pins 0, 1, 6, and 7, until the direction bits are correctly set, defining bit 2 and 3
as low and redefining bits 0 and 1 as strong high drivers.
Figure
r16,(1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0)
r17,(1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0)
PORTB,r16
DDRB,r17
r16,PINB
10-2, the digital input signal can be clamped to ground at the input of the
(1)
“Alternate Port Functions” on page
CC
77.
/2.
7593K–AVR–11/09