AT90USB647-MU Atmel, AT90USB647-MU Datasheet - Page 94

• Manufacturer Part Number: AT90USB647-MU
• Description: MCU, 8BIT, 64K FLASH, USB, 64QFN
• Manufacturer: Atmel

Specifications of AT90USB647-MU

• Controller Family/series: AT90
• No. Of I/o's: 48
• Eeprom Memory Size: 2KB
• Ram Memory Size: 4KB
• Cpu Speed: 16MHz
• No. Of: RoHS Compliant
• Core Size: 8bit
• Program Memory Size: 64KB
• Oscillator Type: External, Internal
• Package: 64QFN EP
• Device Core: AVR
• Family Name: AT90
• Maximum Speed: 20 MHz
• Ram Size: 4 KB
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 48
• Interface Type: SPI/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Operating Temperature: -40 to 85 °C
• Number Of Timers: 4
• Lead Free Status / Rohs Status: Details

11. External Interrupts
11.0.1
94
AT90USB64/128
External Interrupt Control Register A – EICRA
The External Interrupts are triggered by the INT7:0 pin or any of the PCINT7..0 pins. Observe
that, if enabled, the interrupts will trigger even if the INT7:0 or PCINT7..0 pins are configured as
outputs. This feature provides a way of generating a software interrupt.
The Pin change interrupt PCI0 will trigger if any enabled PCINT7:0 pin toggles. PCMSK0 Regis-
ter control which pins contribute to the pin change interrupts. Pin change interrupts on PCINT7
..0 are detected asynchronously. This implies that these interrupts can be used for waking the
part also from sleep modes other than Idle mode.
The External Interrupts can be triggered by a falling or rising edge or a low level. This is set up
as indicated in the specification for the External Interrupt Control Registers – EICRA (INT3:0)
and EICRB (INT7:4). When the external interrupt is enabled and is configured as level triggered,
the interrupt will trigger as long as the pin is held low. Note that recognition of falling or rising
edge interrupts on INT7:4 requires the presence of an I/O clock, described in
Clock Options” on page
asynchronously. This implies that these interrupts can be used for waking the part also from
sleep modes other than Idle mode. The I/O clock is halted in all sleep modes except Idle mode.
Note that if a level triggered interrupt is used for wake-up from Power-down, the required level
must be held long enough for the MCU to complete the wake-up to trigger the level interrupt. If
the level disappears before the end of the Start-up Time, the MCU will still wake up, but no inter-
rupt will be generated. The start-up time is defined by the SUT and CKSEL Fuses as described
in
The External Interrupt Control Register A contains control bits for interrupt sense control.
• Bits 7..0 – ISC31, ISC30 – ISC00, ISC00: External Interrupt 3 - 0 Sense Control Bits
The External Interrupts 3 - 0 are activated by the external pins INT3:0 if the SREG I-flag and the
corresponding interrupt mask in the EIMSK is set. The level and edges on the external pins that
activate the interrupts are defined in
nously. Pulses on INT3:0 pins wider than the minimum pulse width given in
generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. If low level
interrupt is selected, the low level must be held until the completion of the currently executing
instruction to generate an interrupt. If enabled, a level triggered interrupt will generate an inter-
rupt request as long as the pin is held low. When changing the ISCn bit, an interrupt can occur.
Therefore, it is recommended to first disable INTn by clearing its Interrupt Enable bit in the
EIMSK Register. Then, the ISCn bit can be changed. Finally, the INTn interrupt flag should be
cleared by writing a logical one to its Interrupt Flag bit (INTFn) in the EIFR Register before the
interrupt is re-enabled.
Bit
Read/Write
Initial Value
“System Clock and Clock Options” on page
7
ISC31
R/W
0
6
ISC30
R/W
0
39. Low level interrupts and the edge interrupt on INT3:0 are detected
5
ISC21
R/W
0
Table
4
ISC20
R/W
0
11-1. Edges on INT3..INT0 are registered asynchro-
39.
3
ISC11
R/W
0
2
ISC10
R/W
0
1
ISC01
0
R/W
0
ISC00
R/W
0
“System Clock and
EICRA
Table 11-2
7593K–AVR–11/09
will