EZ80F920120MOD Zilog, EZ80F920120MOD Datasheet - Page 122
EZ80F920120MOD
Manufacturer Part Number
EZ80F920120MOD
Description
MODULE EZ80F92 512K 20MHZ
Manufacturer
Zilog
Datasheets
1.EZ80F920120MOD.pdf
(269 pages)
2.EZ80F920120MOD.pdf
(4 pages)
3.EZ80F920120MOD.pdf
(2 pages)
Specifications of EZ80F920120MOD
Module/board Type
Development Module
Processor Series
EZ80F92x
Core
eZ80
Data Bus Width
8 bit
Program Memory Type
Flash
Program Memory Size
1 MB
Interface Type
Cable
Maximum Clock Frequency
20 MHz
Operating Supply Voltage
0 V to 3.3 V
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Package / Case
LQFP
Development Tools By Supplier
eZ80F920200ZCOG
Minimum Operating Temperature
0 C
For Use With/related Products
eZ80F92
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
269-3157
EZ80F920120MOD
EZ80F920120MOD
- Current page: 122 of 269
- Download datasheet (4Mb)
PS015308-0404
UART Recommended Usage
The following is the standard sequence of events that occur in the eZ80F92 device using
the UART. A description of each follows.
•
•
•
Module Reset
Upon reset, all internal registers are set to their default values. All command status regis-
ters are programmed with their default values, and the FIFOs are flushed.
Control Transfers
Based on the requirements of the application, the data transfer baud rate is determined and
the BRG is configured to generate a 16X clock frequency. Interrupts are disabled and the
communication control parameters are programmed in the UARTx_LCTL register. The
FIFO configuration is determined and the receive trigger levels are set in the
UARTx_FCTL register. The status registers, UARTx_LSR and UARTx_MSR, are read,
and ensure that none of the interrupt sources are active. The interrupts are enabled (except
for the transmit interrupt) and the application is ready to use the module for transmission/
reception.
Data Transfers
Transmit.
immediately expected in response. The application reads the UARTx_IIR register and
determines whether the interrupt occurs due to an empty UARTx_THR register or due to a
completed transmission. Upon this determination, the application writes the pertinent
transmit data bytes to the UARTx_THR register. The number of bytes that the application
writes depends on whether or not the FIFO is enabled. If the FIFO is enabled, the applica-
tion can write 16 bytes at a time. If not, the application can write one byte at a time. As a
result of the first Write, the interrupt is deactivated. The processor then waits for the next
interrupt. When the interrupt is raised by the UART module, the processor repeats the
same process until it exhausts all of the data for transmission.
To control and check the modem status, the application sets up the modem by writing to
the UARTx_MCTL register and reading the UARTx_MCTL register before starting the
process mentioned above.
Receive.
RxD input signal. When an interrupt is raised by the UART module, the application reads
the UARTx_IIR register and determines the cause for the interrupt. If the cause is a line
status interrupt, the application reads the UARTx_LSR register, reads the data byte and
Module reset
Control transfers to configure UART operation
Data transfers
The receiver is always enabled, and it continually checks for the start bit on the
To transmit data, the application enables the transmit interrupt. An interrupt is
P R E L I M I N A R Y
Universal Asynchronous Receiver/Transmitter
Product Specification
eZ80F92/eZ80F93
110
Related parts for EZ80F920120MOD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: