ATmega169P Automotive Atmel Corporation, ATmega169P Automotive Datasheet - Page 295

no-image

ATmega169P Automotive

Manufacturer Part Number
ATmega169P Automotive
Description
Manufacturer
Atmel Corporation

Specifications of ATmega169P Automotive

Flash (kbytes)
16 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
54
Ext Interrupts
17
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
100
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
7735B–AVR–12/07
Table 26-4.
Note:
Table 26-5.
Note:
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are locked if
Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the Lock bits.
Fuse High Byte
OCDEN
JTAGEN
SPIEN
WDTON
EESAVE
BOOTSZ1
BOOTSZ0
BOOTRST
Fuse Low Byte
CKDIV8
CKOUT
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
(1)
1. The SPIEN Fuse is not accessible in serial programming mode.
2. The default value of BOOTSZ1..0 results in maximum Boot Size. See
3. See
4. Never ship a product with the OCDEN Fuse programmed regardless of the setting of Lock bits
5. If the JTAG interface is left unconnected, the JTAGEN fuse should if possible be disabled. This
1. The default value of SUT1..0 results in maximum start-up time for the default clock source.
2. The default setting of CKSEL3..0 results in internal RC Oscillator @ 8 MHz. See
3. The CKOUT Fuse allow the system clock to be output on PORTE7. See
4. See
(3)
(4)
(4)
(3)
(5)
for details.
and JTAGEN Fuse. A programmed OCDEN Fuse enables some parts of the clock system to
be running in all sleep modes. This may increase the power consumption.
to avoid static current at the TDO pin in the JTAG interface.
See
page 35
on page 37
Fuse High Byte
Fuse Low Byte
”WDTCR – Watchdog Timer Control Register” on page 54
Table 27-3 on page 328
”System Clock Prescaler” on page 37
for details.
Bit No
Bit No
7
6
5
4
3
2
1
0
7
6
for details.
5
4
3
2
1
0
Description
Enable OCD
Enable JTAG
Enable Serial Program and Data
Downloading
Watchdog Timer always on
EEPROM memory is preserved
through the Chip Erase
Select Boot Size (see
for details)
Select Boot Size (see
for details)
Select Reset Vector
Description
Divide clock by 8
Clock output
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
for details.
ATmega169P Automotive
Table 25-6
Table 25-6
for details.
Default Value
0 (programmed)
1 (unprogrammed)
1 (unprogrammed)
0 (programmed)
0 (programmed)
0 (programmed)
1 (unprogrammed)
0 (programmed)
Default Value
1 (unprogrammed, OCD disabled)
0 (programmed, JTAG enabled)
0 (programmed, SPI prog.
enabled)
1 (unprogrammed)
1 (unprogrammed, EEPROM not
preserved)
0 (programmed)
0 (programmed)
1 (unprogrammed)
for details.
Table 25-6 on page 289
”Clock Output Buffer”
(1)
(2)
(2)
(2)
(2)
(2)
(1)
(2)
Table 7-9 on
295

Related parts for ATmega169P Automotive