ATmega169P Automotive Atmel Corporation, ATmega169P Automotive Datasheet - Page 60

• Manufacturer Part Number: ATmega169P Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega169P Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.2.1
60
ATmega169P Automotive
MCUCR – MCU Control Register
• Bit 1 – IVSEL: Interrupt Vector Select
When the IVSEL bit is cleared (zero), the Interrupt Vectors are placed at the start of the Flash
memory. When this bit is set (one), the Interrupt Vectors are moved to the beginning of the Boot
Loader section of the Flash. The actual address of the start of the Boot Flash Section is deter-
mined by the BOOTSZ Fuses. Refer to the section
Self-Programming” on page 277
• Bit 0 – IVCE: Interrupt Vector Change Enable
The IVCE bit must be written to logic one to enable change of the IVSEL bit. IVCE is cleared by
hardware four cycles after it is written or when IVSEL is written. Setting the IVCE bit will disable
interrupts, as explained in the description in
Space” on page
Bit
0x35 (0x55)
Read/Write
Initial Value
Assembly Code Example
C Code Example
Move_interrupts:
; Get MCUCR
in r16, MCUCR
mov r17, r16
; Enable change of Interrupt Vectors
ori r16, (1<<IVCE)
out MCUCR, r16
; Move interrupts to Boot Flash section
ori r17, (1<<IVSEL)
out MCUCR, r17
ret
void Move_interrupts(void)
{
/* Get MCUCR*/
/* Enable change of Interrupt Vectors */
/* Move interrupts to Boot Flash section
}
uchar temp;
temp = MCUCR;
MCUCR = temp | (1<<IVCE);
*/ MCUCR = temp | (1<<IVSEL);
JTD
R/W
59. See Code Example.
7
0
R
6
0
-
for details.
R
5
0
-
PUD
R/W
4
0
”Moving Interrupts Between Application and Boot
”Boot Loader Support – Read-While-Write
R
3
–
0
R
2
–
0
IVSEL
R/W
1
0
IVCE
R/W
0
0
7735B–AVR–12/07
MCUCR