SC2200 NSC [National Semiconductor], SC2200 Datasheet - Page 431

• Manufacturer Part Number: SC2200
• Description: Thin Client On a Chip
• Manufacturer: NSC [National Semiconductor]

Revision 3.0
Support Documentation
Section
General Description /
Features
Section 1.0 "Architec-
ture Overview"
Section 2.0 "Signal
Definitions"
Section 3.0 "General
Configuration Block"
Section 4.0 "SuperI/O
Module"
Section 5.0 "Core
Logic Module"
Section 6.0 "Video
Processor Module"
Revision
• No changes.
• No changes.
• Table 2-2 "432-EBGA Ball Assignment - Sorted by Ball Number" on page 22:
• Table 2-4 "481-TEPBGA Ball Assignment - Sorted by Ball Number" on page 37:
• Table 2-7 "Two-Signal/Group Multiplexing" on page 52:
• Section 2.4.8 "Low Pin Count (LPC) Bus Interface Signals" on page 67:
• Section 2.4.12 "Parallel Port Interface Signals" on page 71:
• Section 2.4.16 "GPIO Interface Signals" on page 75:
•
• Table 3-1 "General Configuration Block Register Summary" on page 80:
• Table 4-32 "ACB Registers" on page 135:
• Physical Region Descriptor Format on 177:
• Table 5-23 "F3BAR0: XpressAUDIO Support Registers Summary" on page 193:
• Table 5-38 "F3BAR0+Memory Offset: XpressAUDIO Configuration Registers" on page
• Table 5-27 "USB_BAR: USB Controller Registers Summary" on page 196:
• Table 5-42 "USB_BAR+Memory Offset: USB Controller Registers" on page 291:
• Figure 6-2 "NTSC 525 Lines, 60 Hz, Odd Field" on page 318:
• Figure 6-3 "NTSC 525 Lines, 60 Hz, Even Field" on page 318:
— Added “(PU
— Added “(PU
— The TEPBGA ball numbers for IDE_ADDR[2:0] and IDE_DATA[15:0] were wrong.
— LPCPD# - Added “/IRRX2” to GPIO38 in the Mux column.
— STB#WRITE - Added “+F_FRAME” to TFTD17 in the Mux column.
— Corrected Mux column for GPIO8 (had “+SDTEST5”, changed to “+SDTEST4”).
— The TEPBGA ball numbers for GPIO14 through GPIO19 were wrong. Fixed to match
— Offset 30h[27] - Corrected TEPBGA ball number for F_AD6 (was A29, changed to
— Offset 30h[9] - Corrected muxing for INTC# and GPIO19 (i.e., setting for PMR[4] was
— Offset 34h[0] - Changed description from Reserved to SDBE0 (Slave Disconnect
— Offset 05h - Changed values to binary: 00010002 (810) to 0001000b and 11111112
— Fixed table cross-reference in first paragraph (changed to Table 5-11).
— Offset 24h - Changed Width column from “---” to “32”.
269:
— Offset 0Ch[16] - Changed last two sentences into one. Now reads, “This bit is set by
— Offset 48h - Changed reset value of from 01000002h to 01000003h.
— Offset 48h - Changed reset value of from 01000002h to 01000003h.
— Changed VSYNC to VSYNC Start and VSYNC End.
— Changed VSYNC to VSYNC Start and VSYNC End.
Fixed to match ball assignment..
ball assignment.
A20).
reversed).
Boundary Enable).
(12710) to 1111111b.
hardware when a codec command is written to the Codec Command register. It
remains set until the command has been sent to the codec.
(Continued)
Table A-2. Edits to Current Revision
22.5
22.5
)” notation to balls AJ10, AK10, AL10 and AJ11, LAD[3:0] functions.
)” notation to balls L29, L30, L31 and M28, LAD[3:0] functions.
431
www.national.com