h8s-2158 Renesas Electronics Corporation., h8s-2158 Datasheet - Page 881

• Manufacturer Part Number: h8s-2158
• Description: Renesas 16-bit Single-chip Microcomputer H8s Family/h8s/2100 Series
• Manufacturer: Renesas Electronics Corporation.

Table 29.2 DC Characteristics (3)
Conditions: V
Notes:
Item
Analog power
supply current
Reference power
supply current
Analog power supply voltage *
RAM standby voltage
1. The flash memory must be programmed or erased within the conditions V
2. Do not leave the AVCC, AVref, and AVSS pins open even if the A/D converter or D/A converter is
3. Includes peripheral module inputs multiplexed on the pin.
4. Maximum voltage applied to port 6 is V
5. P80/ExIRQ8/SCL0, P81/ExIRQ9/SDA0, P82/ExIRQ10/SCL1, and P83/ExIRQ11/SDA1 are NMOS
6. Indicates values when ICE in ICCR is 0. Low level output when the bus drive function is selected is
7. Current consumption values are for V
8. The values are for V
Even if the A/D converter or D/A converter is not used, apply a value in the range from 2.0 V to 3.6
V to the AVCC and AVref pins by connection to the power supply (V
these two pins should be AV
of V
output voltage is applied to port 6.
push-pull outputs.
An external pull-up resistor is necessary to provide high-level output from SCL0, SCL1, SDA0, and
SDA1 (ICE in ICCR is 1).
P80 to P83, P87, P84/SCK0, P85/SCK1, and P86/SCK2 (ICE in ICCR is 0) high levels are driven
by NMOS. An external pull-up resistor is necessary to provide high-level output from these pins
when they are used as an output.
rated separately.
unloaded and the on-chip pull-up MOSs in the off state.
not used.
V
CC
CC
SS
+ 0.3 V or AV
= AV
= 2.7 V to 3.6 V *
During A/D or
D/A conversion
Waiting for A/D or
D/A conversion
During A/D conversion
During A/D or D/A
conversion
Waiting for A/D or
D/A conversion
SS
*
2
1
= 0 V
CC
RAM
+ 0.3 V when the CIN input is selected. If port 6 is in output mode, the
V
1
CC
, AV
ref
< 2.7 V, V
AV
CC
Symbol Min
AI
AI
AV
V
RAM
CC
*
CC
ref
CC
2
IH
.
CC
= 2.7 V to 3.6 V, AV
min = V
IH
+ 0.3 V when the CIN input is not selected, or the lower
min = V
—
—
—
—
—
2.7
2.0
2.0
CC
– 0.2 V and V
CC
Rev. 3.00 Jan 25, 2006 page 829 of 872
Typ
1.2
0.01
0.5
2.0
0.01
—
—
—
– 0.2 V, and V
Section 29 Electrical Characteristics
Max
2.0
5.0
1.0
5.0
5.0
3.6
3.6
—
ref
IL
*
max = 0.2 V with all output pins
2
IL
CC
Unit
mA
µA
mA
µA
V
= 2.7 V to AV
max = 0.2 V.
). The relationship between
CC
Test Conditions
AV
AV
Operating
Idle/not used
= 3.0 V to 3.6 V.
REJ09B0286-0300
CC
ref
= 2.0 V to 3.6 V *
= 2.0 V to AVcc *
CC
,
2
2